Product Overview Features Applications 1 ESP32 Series Comparison 1.1 Nomenclature 1.2 Comparison 2 Pins 2.1 Pin Layout 2.2 Pin Overview 2.3 IO Pins 2.3.1 Restrictions for GPIOs and RTC_GPIOs 2.4 Analog Pins 2.5 Power Supply 2.5.1 Power Pins 2.5.2 Power Scheme 2.5.3 Chip Power-up and Reset 2.6 Pin Mapping Between Chip and Flash/PSRAM 3 Boot Configurations 3.1 Chip Boot Mode Control 3.2 Internal LDO (VDD_SDIO) Voltage Control 3.3 U0TXD Printing Control 3.4 Timing Control of SDIO Slave 3.5 JTAG Signal Source Control 4 Functional Description 4.1 CPU and Memory 4.1.1 CPU 4.1.2 Internal Memory 4.1.3 External Flash and RAM 4.1.4 Address Mapping Structure 4.1.5 Cache 4.2 System Clocks 4.2.1 CPU Clock 4.2.2 RTC Clock 4.2.3 Audio PLL Clock 4.3 RTC and Low-power Management 4.3.1 Power Management Unit (PMU) 4.3.2 Ultra-Low-Power Coprocessor 4.4 Timers and Watchdogs 4.4.1 General Purpose Timers 4.4.2 Watchdog Timers 4.5 Cryptographic Hardware Accelerators 4.6 Radio and Wi-Fi 4.6.1 2.4 GHz Receiver 4.6.2 2.4 GHz Transmitter 4.6.3 Clock Generator 4.6.4 Wi-Fi Radio and Baseband 4.6.5 Wi-Fi MAC 4.7 Bluetooth 4.7.1 Bluetooth Radio and Baseband 4.7.2 Bluetooth Interface 4.7.3 Bluetooth Stack 4.7.4 Bluetooth Link Controller 4.8 Digital Peripherals 4.8.1 General Purpose Input / Output Interface (GPIO) 4.8.2 Serial Peripheral Interface (SPI) 4.8.3 Universal Asynchronous Receiver Transmitter (UART) 4.8.4 I2C Interface 4.8.5 I2S Interface 4.8.6 Remote Control Peripheral 4.8.7 Pulse Counter Controller (PCNT) 4.8.8 LED PWM Controller 4.8.9 Motor Control PWM 4.8.10 SD/SDIO/MMC Host Controller 4.8.11 SDIO/SPI Slave Controller 4.8.12 TWAI Controller 4.8.13 Ethernet MAC Interface 4.9 Analog Peripherals 4.9.1 Analog-to-Digital Converter (ADC) 4.9.2 Digital-to-Analog Converter (DAC) 4.9.3 Touch Sensor 4.10 Peripheral Pin Configurations 5 Electrical Characteristics 5.1 Absolute Maximum Ratings 5.2 Recommended Power Supply Characteristics 5.3 DC Characteristics (3.3 V, 25 °C) 5.4 RF Current Consumption in Active Mode 5.5 Reliability 5.6 Wi-Fi Radio 5.7 Bluetooth Radio 5.7.1 Receiver – Basic Data Rate 5.7.2 Transmitter – Basic Data Rate 5.7.3 Receiver – Enhanced Data Rate 5.7.4 Transmitter – Enhanced Data Rate 5.8 Bluetooth LE Radio 5.8.1 Receiver 5.8.2 Transmitter 6 Packaging Related Documentation and Resources Appendix A – ESP32 Pin Lists A.1. Notes on ESP32 Pin Lists A.2. GPIO_Matrix A.3. Ethernet_MAC A.4. IO_MUX Revision History ESP32 Series Datasheet Version 5.2 2.4 GHz Wi-Fi + Bluetooth ® + Bluetooth LE SoC Including: ESP32-D0WD-V3 ESP32-U4WDH ESP32-S0WD – Not Recommended for New Designs (NRND) ESP32-D0WD – Not Recommended for New Designs (NRND) ESP32-D0WDQ6 – Not Recommended for New Designs (NRND) ESP32-D0WDQ6-V3 – Not Recommended for New Designs (NRND) ESP32-D0WDR2-V3 – End of Life (EOL), upgraded to ESP32-D0WDRH2-V3 www.espressif.com Product Overview ESP32 is a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip designed with the TSMC low-power 40 nm technology. It is designed to achieve the best power and RF performance, showing robustness, versatility and reliability in a wide variety of applications and power scenarios. For details on part numbers and ordering information, please refer to Section 1 ESP32 Series Comparison. For details on chip revisions, please refer to ESP32 Chip Revision v3.0 User Guide and ESP32 Series SoC Errata. The functional block diagram of the SoC is shown below. Core and memory ROM Cryptographic hardware acceleration AES SHA RSA RTC ULP coprocessor Recovery memory PMU Bluetooth link controller Bluetooth baseband Wi-Fi MAC Wi-Fi baseband SPI 2 (or 1) x Xtensa® 32-bit LX6 Microprocessors RF receive RF transmit Switch Balun I2C I2S SDIO UART TWAI® ETH RMT PWM Touch sensor DAC ADC Clock generator RNG SRAM In-Package Flash or PSRAM Timers ESP32 Functional Block Diagram Espressif Systems 2 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Features Wi-Fi • 802.11b/g/n • 802.11n (2.4 GHz), up to 150 Mbps • WMM • TX/RX A-MPDU, RX A-MSDU • Immediate Block ACK • Defragmentation • Automatic Beacon monitoring (hardware TSF) • Four virtual Wi-Fi interfaces • Simultaneous support for Infrastructure Station, SoftAP, and Promiscuous modes Note that when ESP32 is in Station mode, performing a scan, the SoftAP channel will be changed. • Antenna diversity Bluetooth ® • Compliant with Bluetooth v4.2 BR/EDR and Bluetooth LE specifications • Class-1, class-2 and class-3 transmitter without external power amplifier • Enhanced Power Control • +9 dBm transmitting power • NZIF receiver with –94 dBm Bluetooth LE sensitivity • Adaptive Frequency Hopping (AFH) • Standard HCI based on SDIO/SPI/UART • High-speed UART HCI, up to 4 Mbps • Bluetooth 4.2 BR/EDR and Bluetooth LE dual mode controller • Synchronous Connection-Oriented/Extended (SCO/eSCO) • CVSD and SBC for audio codec • Bluetooth Piconet and Scatternet • Multi-connections in Classic Bluetooth and Bluetooth LE • Simultaneous advertising and scanning CPU and Memory • Xtensa ® single-/dual-core 32-bit LX6 microprocessor(s) • CoreMark ® score: – 1 core at 240 MHz: 539.98 CoreMark; 2.25 CoreMark/MHz Espressif Systems 3 Submit Documentation Feedback ESP32 Series Datasheet v5.2 – 2 cores at 240 MHz: 1079.96 CoreMark; 4.50 CoreMark/MHz • 448 KB ROM • 520 KB SRAM • 16 KB SRAM in RTC • QSPI supports multiple flash/SRAM chips Clocks and Timers • Internal 8 MHz oscillator with calibration • Internal RC oscillator with calibration • External 2 MHz ~ 60 MHz crystal oscillator (40 MHz only for Wi-Fi/Bluetooth functionality) • External 32 kHz crystal oscillator for RTC with calibration • Two timer groups, including 2 × 64-bit timers and 1 × main watchdog in each group • One RTC timer • RTC watchdog Advanced Peripheral Interfaces • 34 programmable GPIOs – Five strapping GPIOs – Six input-only GPIOs – Six GPIOs needed for in-package flash (ESP32-U4WDH) and in-package PSRAM (ESP32-D0WDRH2-V3) • 12-bit SAR ADC up to 18 channels • Two 8-bit DAC • 10 touch sensors • Four SPI interfaces • Two I2S interfaces • Two I2C interfaces • Three UART interfaces • One host (SD/eMMC/SDIO) • One slave (SDIO/SPI) • Pulse count controller • Ethernet MAC interface with dedicated DMA and IEEE 1588 support • TWAI ® , compatible with ISO 11898-1 (CAN Specification 2.0) • RMT (TX/RX) Espressif Systems 4 Submit Documentation Feedback ESP32 Series Datasheet v5.2 • Motor PWM • LED PWM up to 16 channels Power Management • Fine-resolution power control through a selection of clock frequency, duty cycle, Wi-Fi operating modes, and individual power control of internal components • Five power modes designed for typical scenarios: Active, Modem-sleep, Light-sleep, Deep-sleep, Hibernation • Power consumption in Deep-sleep mode is 10 µA • Ultra-Low-Power (ULP) coprocessors • RTC memory remains powered on in Deep-sleep mode Security • Secure boot • Flash encryption • 1024-bit OTP, up to 768-bit for customers • Cryptographic hardware acceleration: – AES – Hash (SHA-2) – RSA – Random Number Generator (RNG) Applications With low power consumption, ESP32 is an ideal choice for IoT devices in the following areas: • Smart Home • Industrial Automation • Health Care • Consumer Electronics • Smart Agriculture • POS Machines • Service Robot • Audio Devices • Generic Low-power IoT Sensor Hubs • Generic Low-power IoT Data Loggers • Cameras for Video Streaming • Speech Recognition • Image Recognition • SDIO Wi-Fi + Bluetooth Networking Card Espressif Systems 5 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Contents Note: Check the link or the QR code to make sure that you use the latest version of this document: https://www.espressif.com/documentation/esp32_datasheet_en.pdf Contents Product Overview 2 Features 3 Applications 5 1 ESP32 Series Comparison 11 1.1 Nomenclature 11 1.2 Comparison 11 2 Pins 12 2.1 Pin Layout 12 2.2 Pin Overview 14 2.3 IO Pins 17 2.3.1 Restrictions for GPIOs and RTC_GPIOs 17 2.4 Analog Pins 17 2.5 Power Supply 17 2.5.1 Power Pins 17 2.5.2 Power Scheme 18 2.5.3 Chip Power-up and Reset 19 2.6 Pin Mapping Between Chip and Flash/PSRAM 20 3 Boot Configurations 22 3.1 Chip Boot Mode Control 23 3.2 Internal LDO (VDD_SDIO) Voltage Control 24 3.3 U0TXD Printing Control 25 3.4 Timing Control of SDIO Slave 25 3.5 JTAG Signal Source Control 25 4 Functional Description 26 4.1 CPU and Memory 26 4.1.1 CPU 26 4.1.2 Internal Memory 26 4.1.3 External Flash and RAM 27 4.1.4 Address Mapping Structure 27 4.1.5 Cache 29 4.2 System Clocks 29 4.2.1 CPU Clock 29 Espressif Systems 6 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Contents 4.2.2 RTC Clock 29 4.2.3 Audio PLL Clock 30 4.3 RTC and Low-power Management 30 4.3.1 Power Management Unit (PMU) 30 4.3.2 Ultra-Low-Power Coprocessor 31 4.4 Timers and Watchdogs 31 4.4.1 General Purpose Timers 31 4.4.2 Watchdog Timers 31 4.5 Cryptographic Hardware Accelerators 32 4.6 Radio and Wi-Fi 32 4.6.1 2.4 GHz Receiver 32 4.6.2 2.4 GHz Transmitter 33 4.6.3 Clock Generator 33 4.6.4 Wi-Fi Radio and Baseband 33 4.6.5 Wi-Fi MAC 34 4.7 Bluetooth 34 4.7.1 Bluetooth Radio and Baseband 34 4.7.2 Bluetooth Interface 34 4.7.3 Bluetooth Stack 35 4.7.4 Bluetooth Link Controller 35 4.8 Digital Peripherals 37 4.8.1 General Purpose Input / Output Interface (GPIO) 37 4.8.2 Serial Peripheral Interface (SPI) 37 4.8.3 Universal Asynchronous Receiver Transmitter (UART) 37 4.8.4 I2C Interface 38 4.8.5 I2S Interface 39 4.8.6 Remote Control Peripheral 39 4.8.7 Pulse Counter Controller (PCNT) 39 4.8.8 LED PWM Controller 40 4.8.9 Motor Control PWM 40 4.8.10 SD/SDIO/MMC Host Controller 41 4.8.11 SDIO/SPI Slave Controller 42 4.8.12 TWAI ® Controller 43 4.8.13 Ethernet MAC Interface 43 4.9 Analog Peripherals 44 4.9.1 Analog-to-Digital Converter (ADC) 44 4.9.2 Digital-to-Analog Converter (DAC) 45 4.9.3 Touch Sensor 45 4.10 Peripheral Pin Configurations 47 5 Electrical Characteristics 52 5.1 Absolute Maximum Ratings 52 5.2 Recommended Power Supply Characteristics 52 5.3 DC Characteristics (3.3 V, 25 °C) 53 5.4 RF Current Consumption in Active Mode 53 5.5 Reliability 54 Espressif Systems 7 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Contents 5.6 Wi-Fi Radio 54 5.7 Bluetooth Radio 55 5.7.1 Receiver –Basic Data Rate 55 5.7.2 Transmitter –Basic Data Rate 55 5.7.3 Receiver –Enhanced Data Rate 56 5.7.4 Transmitter –Enhanced Data Rate 56 5.8 Bluetooth LE Radio 57 5.8.1 Receiver 57 5.8.2 Transmitter 58 6 Packaging 59 Related Documentation and Resources 60 Appendix A –ESP32 Pin Lists 61 A.1. Notes on ESP32 Pin Lists 61 A.2. GPIO_Matrix 63 A.3. Ethernet_MAC 68 A.4. IO_MUX 68 Revision History 70 Espressif Systems 8 Submit Documentation Feedback ESP32 Series Datasheet v5.2 List of Tables List of Tables 1-1 ESP32 Series Comparison 11 2-1 Pin Overview 14 2-2 Analog Pins 17 2-3 Power Pins 18 2-4 Description of Timing Parameters for Power-up and Reset 19 2-5 Pin-to-Pin Mapping Between Chip and In-Package Flash/PSRAM 20 2-6 Pin-to-Pin Mapping Between Chip and Off-Package Flash/PSRAM 20 3-1 Default Configuration of Strapping Pins 22 3-2 Description of Timing Parameters for the Strapping Pins 23 3-3 Chip Boot Mode Control 23 3-4 U0TXD Printing Control 25 3-5 Timing Control of SDIO Slave 25 4-1 Memory and Peripheral Mapping 28 4-2 Power Consumption by Power Modes 30 4-3 ADC Characteristics 44 4-4 ADC Calibration Results 45 4-5 Capacitive-Sensing GPIOs Available on ESP32 46 4-6 Peripheral Pin Configurations 47 5-1 Absolute Maximum Ratings 52 5-2 Recommended Power Supply Characteristics 52 5-3 DC Characteristics (3.3 V, 25 °C) 53 5-4 Current Consumption Depending on RF Modes 53 5-5 Reliability Qualifications 54 5-6 Wi-Fi Radio Characteristics 54 5-7 Receiver Characteristics –Basic Data Rate 55 5-8 Transmitter Characteristics –Basic Data Rate 55 5-9 Receiver Characteristics –Enhanced Data Rate 56 5-10 Transmitter Characteristics –Enhanced Data Rate 57 5-11 Receiver Characteristics –Bluetooth LE 57 5-12 Transmitter Characteristics –Bluetooth LE 58 6-1 Notes on ESP32 Pin Lists 61 6-2 GPIO_Matrix 63 6-3 Ethernet_MAC 68 Espressif Systems 9 Submit Documentation Feedback ESP32 Series Datasheet v5.2 List of Figures List of Figures 1-1 ESP32 Series Nomenclature 11 2-1 ESP32 Pin Layout (QFN 6*6, Top View) 12 2-2 ESP32 Pin Layout (QFN 5*5, Top View) 13 2-3 ESP32 Power Scheme 18 2-4 Visualization of Timing Parameters for Power-up and Reset 19 3-1 Visualization of Timing Parameters for the Strapping Pins 23 3-2 Chip Boot Flow 24 4-1 Address Mapping Structure 27 6-1 QFN48 (6x6 mm) Package 59 6-2 QFN48 (5x5 mm) Package 59 Espressif Systems 10 Submit Documentation Feedback ESP32 Series Datasheet v5.2 1 ESP32 Series Comparison 1 ESP32 Series Comparison 1.1 Nomenclature ESP32 D WD Chip Series Core D/U: Dual core S: Single core Connection WD: Wi-Fi b/g/n + Bluetooth/Bluetooth LE dual mode R2 H In-package PSRAM R2: 2 MB PSRAM High temperature 0 In-package flash 0: No in-package flash 2: 2 MB flash 4: 4 MB flash Q6 Chip revision v3.0 or newer V3 Package Q6: QFN 6*6 N/A: QFN 5*5 Figure 1-1. ESP32 Series Nomenclature 1.2 Comparison Table 1-1. ESP32 Series Comparison Part Number 1 Core Chip Revision 2 In-Package Flash/PSRAM Package VDD_SDIO Voltage ESP32-D0WD-V3 Dual core v3.0/v3.1 4 — QFN 5*5 1.8 V/3.3 V ESP32-D0WDR2-V3 (EOL) Upgraded to ESP32-D0WDRH2-V3 7 Dual core v3.0/v3.1 4 2 MB PSRAM QFN 5*5 3.3 V ESP32-U4WDH Dual core 3 v3.0/v3.1 4 4 MB flash 6 QFN 5*5 3.3 V ESP32-D0WDQ6-V3 (NRND) Dual core v3.0/v3.1 4 — QFN 6*6 1.8 V/3.3 V ESP32-D0WD (NRND) Dual core v1.0/v1.1 5 — QFN 5*5 1.8 V/3.3 V ESP32-D0WDQ6 (NRND) Dual core v1.0/v1.1 5 — QFN 6*6 1.8 V/3.3 V ESP32-S0WD (NRND) Single core v1.0/v1.1 5 — QFN 5*5 1.8 V/3.3 V 1 All above chips support Wi-Fi b/g/n + Bluetooth/Bluetooth LE Dual Mode connection. For details on chip marking and packing, see Section 6 Packaging. 2 Differences between ESP32 chip revisions and how to distinguish them are described in ESP32 Series SoC Errata. 3 ESP32-U4WDH will be produced as dual-core instead of single core. See PCN-2021-021 for details. 4 The chips will be produced with chip revision v3.1 inside. See PCN20220901 for details. 5 The chips will be produced with chip revision v1.1 inside. See PCN20220901 for details. 6 The in-package flash supports: - More than 100,000 program/erase cycles - More than 20 years data retention time 7 ESP32-D0WDR2-V3 is end of life and upgraded to ESP32-D0WDRH2-V3. See PCN20251001 for details. Espressif Systems 11 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins 2 Pins 2.1 Pin Layout 32K_XP 12 VDET_2 11 10 9 8 7 6 5 4 3 2 1 VDET_1 CHIP_PU SENSOR_VN SENSOR_CAPN SENSOR_CAPP SENSOR_VP VDD3P3 VDD3P3 LNA_IN VDDA 25 26 27 28 29 30 31 32 33 34 35 36 GPIO16 VDD_SDIO GPIO5 VDD3P3_CPU37 GPIO1938 39 40 41 42 43 44 45 46 47 48 GPIO22 U0RXD U0TXD GPIO21 XTAL_N XTAL_P VDDA CAP2 CAP1 GPIO2 24 MTDO 23 22 21 20 19 18 17 16 15 14 13 MTCK VDD3P3_RTC MTDI MTMS GPIO27 GPIO26 GPIO25 32K_XN SD_DATA_2 SD_DATA_3 SD_CMD SD_CLK SD_DATA_0 SD_DATA_1 GPIO4 GPIO0 GPIO23 GPIO18 VDDA GPIO17 ESP32 49 GND Figure 2-1. ESP32 Pin Layout (QFN 6*6, Top View) Espressif Systems 12 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins 10 9 8 7 6 5 4 3 2 1 VDET_1 CHIP_PU SENSOR_VN SENSOR_CAPN SENSOR_CAPP SENSOR_VP VDD3P3 VDD3P3 LNA_IN VDDA 25 26 27 28 29 30 31 32 33 34 GPIO16 VDD_SDIO GPIO5 VDD3P3_CPU GPIO19 39 40 41 42 43 44 45 46 47 48 GPIO22 U0RXD U0TXD GPIO21 XTAL_N XTAL_P VDDA CAP2 CAP1 GPIO2 24 MTDO 23 22 21 20 19 18 17 16 15 MTCK VDD3P3_RTC MTDI MTMS GPIO27 GPIO26 GPIO25 32K_XN SD_DATA_2 SD_DATA_3 SD_CMD SD_CLK SD_DATA_0 SD_DATA_1 GPIO4 GPIO0 VDDA GPIO1732K_XP VDET_2 GPIO18 GPIO23 11 12 13 14 35 36 37 38 ESP32 49 GND Figure 2-2. ESP32 Pin Layout (QFN 5*5, Top View) Espressif Systems 13 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins 2.2 Pin Overview Table 2-1. Pin Overview Name No. Type Function Analog VDDA 1 P Analog power supply (2.3 V ∼ 3.6 V) LNA_IN 2 I/O RF input and output VDD3P3 3 P Analog power supply (2.3 V ∼ 3.6 V) VDD3P3 4 P Analog power supply (2.3 V ∼ 3.6 V) VDD3P3_RTC SENSOR_VP 5 I GPIO36, ADC1_CH0, RTC_GPIO0 SENSOR_CAPP 6 I GPIO37, ADC1_CH1, RTC_GPIO1 SENSOR_CAPN 7 I GPIO38, ADC1_CH2, RTC_GPIO2 SENSOR_VN 8 I GPIO39, ADC1_CH3, RTC_GPIO3 CHIP_PU 9 I High: On; enables the chip Low: Off; the chip shuts down Note: Do not leave the CHIP_PU pin floating. VDET_1 10 I GPIO34, ADC1_CH6, RTC_GPIO4 VDET_2 11 I GPIO35, ADC1_CH7, RTC_GPIO5 32K_XP 12 I/O GPIO32, ADC1_CH4, RTC_GPIO9, TOUCH9, 32K_XP (32.768 kHz crystal oscillator input) 32K_XN 13 I/O GPIO33, ADC1_CH5, RTC_GPIO8, TOUCH8, 32K_XN (32.768 kHz crystal oscillator output) GPIO25 14 I/O GPIO25, ADC2_CH8, RTC_GPIO6, DAC_1, EMAC_RXD0 GPIO26 15 I/O GPIO26, ADC2_CH9, RTC_GPIO7, DAC_2, EMAC_RXD1 GPIO27 16 I/O GPIO27, ADC2_CH7, RTC_GPIO17, TOUCH7, EMAC_RX_DV MTMS 17 I/O GPIO14, ADC2_CH6, RTC_GPIO16, TOUCH6, EMAC_TXD2, HSPICLK, HS2_CLK, SD_CLK, MTMS MTDI 18 I/O GPIO12, ADC2_CH5, RTC_GPIO15, TOUCH5, EMAC_TXD3, HSPIQ, HS2_DATA2, SD_DATA2, MTDI VDD3P3_RTC 19 P Input power supply for RTC IO (2.3 V ∼ 3.6 V) MTCK 20 I/O GPIO13, ADC2_CH4, RTC_GPIO14, TOUCH4, EMAC_RX_ER, HSPID, HS2_DATA3, SD_DATA3, MTCK MTDO 21 I/O GPIO15, ADC2_CH3, RTC_GPIO13, TOUCH3, EMAC_RXD3, HSPICS0, HS2_CMD, SD_CMD, MTDO Espressif Systems 14 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins Name No. Type Function GPIO2 22 I/O GPIO2, ADC2_CH2, RTC_GPIO12, TOUCH2, HSPIWP, HS2_DATA0, SD_DATA0 GPIO0 23 I/O GPIO0, ADC2_CH1, RTC_GPIO11, TOUCH1, EMAC_TX_CLK, CLK_OUT1, GPIO4 24 I/O GPIO4, ADC2_CH0, RTC_GPIO10, TOUCH0, EMAC_TX_ER, HSPIHD, HS2_DATA1, SD_DATA1 VDD_SDIO GPIO16 25 I/O GPIO16, HS1_DATA4, U2RXD, EMAC_CLK_OUT VDD_SDIO 26 P Output power supply: 1.8 V or the same voltage as VDD3P3_RTC GPIO17 27 I/O GPIO17, HS1_DATA5, U2TXD, EMAC_CLK_OUT_180 SD_DATA_2 28 I/O GPIO9, HS1_DATA2, U1RXD, SD_DATA2, SPIHD SD_DATA_3 29 I/O GPIO10, HS1_DATA3, U1TXD, SD_DATA3, SPIWP SD_CMD 30 I/O GPIO11, HS1_CMD, U1RTS, SD_CMD, SPICS0 SD_CLK 31 I/O GPIO6, HS1_CLK, U1CTS, SD_CLK, SPICLK SD_DATA_0 32 I/O GPIO7, HS1_DATA0, U2RTS, SD_DATA0, SPIQ SD_DATA_1 33 I/O GPIO8, HS1_DATA1, U2CTS, SD_DATA1, SPID VDD3P3_CPU GPIO5 34 I/O GPIO5, HS1_DATA6, VSPICS0, EMAC_RX_CLK GPIO18 35 I/O GPIO18, HS1_DATA7, VSPICLK GPIO23 36 I/O GPIO23, HS1_STROBE, VSPID VDD3P3_CPU 37 P Input power supply for CPU IO (1.8 V ∼ 3.6 V) GPIO19 38 I/O GPIO19, U0CTS, VSPIQ, EMAC_TXD0 GPIO22 39 I/O GPIO22, U0RTS, VSPIWP, EMAC_TXD1 U0RXD 40 I/O GPIO3, U0RXD, CLK_OUT2 U0TXD 41 I/O GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2 GPIO21 42 I/O GPIO21, VSPIHD, EMAC_TX_EN Analog VDDA 43 P Analog power supply (2.3 V ∼ 3.6 V) XTAL_N 44 O External crystal output XTAL_P 45 I External crystal input VDDA 46 P Analog power supply (2.3 V ∼ 3.6 V) CAP2 47 I Connects to a 3.3 nF (10%) capacitor and 20 kΩ resistor in parallel to CAP1 Espressif Systems 15 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins Name No. Type Function CAP1 48 I Connects to a 10 nF series capacitor to ground GND 49 P Ground Notes for Table 2-1 Pin Overview: 1. Function names: CLK_OUT… clock output SPICLK HSPICLK VSPICLK        SPI clock signal HS…_CLK SDIO Master clock signal SD_CLK SDIO Slave clock signal EMAC_TX_CLK EMAC_RX_CLK } EMAC clock signal U…_RTS U…_CTS } UART0/1/2 hardware flow control signals U…_RXD U…_TXD } UART0/1/2 receive/transmit signals MTMS MTDI MTCK MTDO            JTAG interface signals GPIO… General-purpose input/output with signals routed via the GPIO matrix. For more details on the GPIO matrix, see ESP32 Technical Reference Manual > Chapter IO MUX and GPIO Matrix。 2. Regarding highlighted cells, see Section 2.3.1 Restrictions for GPIOs and RTC_GPIOs. 3. For a quick reference guide to using the IO_MUX, Ethernet MAC, and GPIO Matrix pins of ESP32, please refer to Appendix ESP32 Pin Lists. Espressif Systems 16 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins 2.3 IO Pins 2.3.1 Restrictions for GPIOs and RTC_GPIOs All IO pins of the ESP32 have GPIO and some have RTC_GPIO pin functions. However, these IO pins are multifunctional and can be configured for different purposes based on the requirements. Some IOs have restrictions for usage. It is essential to consider their multiplexed nature and the limitations when using these IO pins. In Table 2-1 Pin Overview some pin functions are highlighted, specically: • GPIO – Input only pins, output is not supported due to lack of pull-up/pull-down resistors. • GPIO – allocated for communication with in-package flash/PSRAM and NOT recommended for other uses. For details, see Section 2.6 Pin Mapping Between Chip and Flash/PSRAM. • GPIO – have one of the following important functions: – Strapping pins – need to be at certain logic levels at startup. See Section 3 Boot Configurations. – JTAG interface – often used for debugging. – UART interface – often used for debugging. See also Appendix A.1 – Notes on ESP32 Pin Lists. 2.4 Analog Pins Table 2-2. Analog Pins Pin Pin Pin Pin No. Name Type Function 2 LNA_IN I/O Low Noise Amplifier (LNA) input signal, Power Amplifier (PA) output signal 9 CHIP_PU I High: on, enables the chip (Powered up). Low: off, the chip powers off (powered down). Note: Do not leave the CHIP_PU pin floating. 44 XTAL_N — External clock input/output connected to chip’s crystal or oscillator. P/N means differential clock positive/negative.45 XTAL_P — 2.5 Power Supply 2.5.1 Power Pins ESP32’s digital pins are divided into three different power domains: • VDD3P3_RTC • VDD3P3_CPU • VDD_SDIO Espressif Systems 17 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins Table 2-3. Power Pins Pin Pin Power Supply No. Name Direction Power Domain / Other IO Pins 1 VDDA Input Analog power domain 3 VDD3P3 Input Analog power domain 4 VDD3P3 Input Analog power domain 19 VDD3P3_RTC 1 Input RTC and part of Digital power domains RTC IO 26 VDD3P3_SDIO 2 Input/Output Analog power domain 37 VDD3P3_CPU 3 Input Digital power domain Digital IO 43 VDDA Input Analog power domain 46 VDDA Input Analog power domain 49 GND – External ground connection 1 VDD3P3_RTC is also the input power supply for RTC and CPU. 2 VDD_SDIO connects to the output of an internal LDO whose input is VDD3P3_RTC. When VDD_SDIO is connected to the same PCB net together with VDD3P3_RTC, the internal LDO is disabled automatically. 3 VDD3P3_CPU is also the input power supply for CPU. 2.5.2 Power Scheme The power scheme is shown in Figure 2-3 ESP32 Power Scheme. SDIO Domain RTC Domain CPU Domain LDOLDO LDO1.8 V 1.1 V1.1 V VDD3P3_RTC VDD3P3_CPU VDD_SDIO 3.3 V/1.8 V R = 6 Ω Figure 2-3. ESP32 Power Scheme Espressif Systems 18 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins The internal LDO can be configured as having 1.8 V, or the same voltage as VDD3P3_RTC. It can be powered off via software to minimize the current of flash/SRAM during the Deep-sleep mode. 2.5.3 Chip Power-up and Reset Once the power is supplied to the chip, its power rails need a short time to stabilize. After that, CHIP_PU – the pin used for power-up and reset – is pulled high to activate the chip. For information on CHIP_PU as well as power-up and reset timing, see Figure 2-4 and Table 2-4. V IL_nRST t ST BL t RST VDD3P3_RTC Min VDD CHIP_PU Figure 2-4. Visualization of Timing Parameters for Power-up and Reset Table 2-4. Description of Timing Parameters for Power-up and Reset Parameter Description Min (µs) t ST BL Time reserved for the 3.3 V rails to stabilize before the CHIP_PU pin is pulled high to activate the chip 50 t RST Time reserved for CHIP_PU to stay below V IL_nRST to reset the chip (see Table 5-3) 50 • In scenarios where ESP32 is powered up and down repeatedly by switching the power rails, while there is a large capacitor on the VDD33 rail and CHIP_PU and VDD33 are connected, simply switching off the CHIP_PU power rail and immediately switching it back on may cause an incomplete power discharge cycle and failure to reset the chip adequately. An additional discharge circuit may be required to accelerate the discharge of the large capacitor on rail VDD33, which will ensure proper power-on-reset when the ESP32 is powered up again. • When a battery is used as the power supply for the ESP32 series of chips and modules, a supply voltage supervisor is recommended, so that a boot failure due to low voltage is avoided. Users are recommended to pull CHIP_PU low if the power supply for ESP32 is below 2.3 V. Notes on power supply: • The operating voltage of ESP32 ranges from 2.3 V to 3.6 V. When using a single-power supply, the recommended voltage of the power supply is 3.3 V, and its recommended output current is 500 mA or more. • PSRAM and flash both are powered by VDD_SDIO. If the chip has an in-package flash, the voltage of VDD_SDIO is determined by the operating voltage of the in-package flash. If the chip also connects to an external PSRAM, the operating voltage of external PSRAM must match that of the in-package flash. This also applies if the chip has an in-package PSRAM but also connects to an external flash. Espressif Systems 19 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins • When VDD_SDIO 1.8 V is used as the power supply for external flash/PSRAM, a 2 kΩ grounding resistor should be added to VDD_SDIO. For the circuit design, please refer to ESP32 Hardware Design Guidelines. • When the three digital power supplies are used to drive peripherals, e.g., 3.3 V flash, they should comply with the peripherals’ specifications. 2.6 Pin Mapping Between Chip and Flash/PSRAM Table 2-5 lists the pin-to-pin mapping between the chip and the in-package flash/PSRAM. The chip pins listed here are not recommended for other usage. For the data port connection between ESP32 and off-package flash/PSRAM please refer to Table 2-6. Table 2-5. Pin-to-Pin Mapping Between Chip and In-Package Flash/PSRAM ESP32-U4WDH In-Package Flash (4 MB) SD_DATA_1 IO0/DI GPIO17 IO1/DO SD_DATA_0 IO2/WP# SD_CMD IO3/HOLD# SD_CLK CLK GPIO16 CS# GND VSS VDD_SDIO 1 VDD ESP32-D0WDRH2-V3 In-Package PSRAM (2 MB) SD_DATA_1 SIO0/SI SD_DATA_0 SIO1/SO SD_DATA_3 SIO2 SD_DATA_2 SIO3 SD_CLK SCLK GPIO16 2 CE# GND VSS VDD_SDIO 1 VDD Table 2-6. Pin-to-Pin Mapping Between Chip and Off-Package Flash/PSRAM Chip Pin Off-Package Flash SD_DATA_1/SPID IO0/DI SD_DATA_0/SPIQ IO1/DO SD_DATA_3/SPIWP IO2/WP# SD_DATA_2/SPIHD IO3/HOLD# SD_CLK CLK SD_CMD CS# GND VSS VDD_SDIO VDD Chip Pin Off-Package PSRAM Cont’d on next page Espressif Systems 20 Submit Documentation Feedback ESP32 Series Datasheet v5.2 2 Pins Table 2-6 – cont’d from previous page Chip Pin Off-Package PSRAM SD_DATA_1 SIO0/SI SD_DATA_0 SIO1/SO SD_DATA_3 SIO2 SD_DATA_2 SIO3 SD_CLK/GPIO17 3 SCLK GPIO16 2 CE# GND VSS VDD_SDIO VDD Note: 1. As the in-package flash (ESP32-U4WDH) and the in-package PSRAM (ESP32-D0WDRH2-V3) operate at 3.3 V, VDD_SDIO must be powered by VDD3P3_RTC via a 6 Ω resistor. See Figure 2-3 ESP32 Power Scheme. 2. If GPIO16 is used to connect to PSRAM’s CE# signal, please add a pull-up resistor at the GPIO16 pin. See ESP32-WROVER-E Datasheet > Figure Schematics of ESP32-WROVER-E. 3. SD_CLK and GPIO17 pins are available to connect to the SCLK signal of external PSRAM. • If SD_CLK pin is selected, one GPIO (i.e., GPIO17) will be saved. The saved GPIO can be used for other purposes. This connection has passed internal tests, but relevant certification has not been completed. • Or GPIO17 pin is used to connect to the SCLK signal. This connection has passed relevant certification, see certificates for ESP32-WROVER-E. Please select the proper pin for your specific applications. Espressif Systems 21 Submit Documentation Feedback ESP32 Series Datasheet v5.2 3 Boot Configurations 3 Boot Configurations The chip allows for configuring the following boot parameters through strapping pins and eFuse bits at power-up or a hardware reset, without microcontroller interaction. • Chip boot mode – Strapping pin: GPIO0 and GPIO2 • Internal LDO (VDD_SDIO) Voltage – Strapping pin: MTDI – eFuse bit: EFUSE_SDIO_FORCE and EFUSE_SDIO_TIEH • U0TXD printing – Strapping pin: MTDO • Timing of SDIO Slave – Strapping pin: MTDO and GPIO5 • JTAG signal source – eFuse bit: EFUSE_DISABLE_JTAG The default values of all the above eFuse bits are 0, which means that they are not burnt. Given that eFuse is one-time programmable, once an eFuse bit is programmed to 1, it can never be reverted to 0. For how to program eFuse bits, please refer to ESP32 Technical Reference Manual > Chapter eFuse Controller. The default values of the strapping pins, namely the logic levels, are determined by pins’internal weak pull-up/pull-down resistors at reset if the pins are not connected to any circuit, or connected to an external high-impedance circuit. Table 3-1. Default Configuration of Strapping Pins Strapping Pin Default Configuration Bit Value GPIO0 Pull-up 1 GPIO2 Pull-down 0 MTDI Pull-down 0 MTDO Pull-up 1 GPIO5 Pull-up 1 To change the bit values, the strapping pins should be connected to external pull-down/pull-up resistances. If the ESP32 is used as a device by a host MCU, the strapping pin voltage levels can also be controlled by the host MCU. All strapping pins have latches. At system reset, the latches sample the bit values of their respective strapping pins and store them until the chip is powered down or shut down. The states of latches cannot be changed in any other way. It makes the strapping pin values available during the entire chip operation, and the pins are freed up to be used as regular IO pins after reset. The timing of signals connected to the strapping pins should adhere to the setup time and hold time specifications in Table 3-2 and Figure 3-1. Espressif Systems 22 Submit Documentation Feedback ESP32 Series Datasheet v5.2 3 Boot Configurations Table 3-2. Description of Timing Parameters for the Strapping Pins Parameter Description Min (ms) t SU Setup time is the time reserved for the power rails to stabilize before the CHIP_PU pin is pulled high to activate the chip. 0 t H Hold time is the time reserved for the chip to read the strapping pin values after CHIP_PU is already high and before these pins start operating as regular IO pins. 1 Strapping pin V IH_nRST V IH t SU t H CHIP_PU Figure 3-1. Visualization of Timing Parameters for the Strapping Pins 3.1 Chip Boot Mode Control GPIO0 and GPIO2 control the boot mode after the reset is released. See Table 3-3 Chip Boot Mode Control. Table 3-3. Chip Boot Mode Control Boot Mode GPIO0 GPIO2 SPI Boot Mode 1 Any value Joint Download Boot Mode 2 0 0 1 Bold marks the default value and configuration. 2 Joint Download Boot mode supports the following download methods: • SDIO Download Boot • UART Download Boot In Joint Download Boot mode, the detailed boot flow of the chip is put below 3-2. Espressif Systems 23 Submit Documentation Feedback ESP32 Series Datasheet v5.2 3 Boot Configurations Figure 3-2. Chip Boot Flow uart_download_dis controls boot mode behaviors: It permanently disables Download Boot mode when uart_download_dis is set to 1 (valid only for ESP32 chip revisions v3.0 and higher). 3.2 Internal LDO (VDD_SDIO) Voltage Control The required VDD_SPI voltage for the chips of the ESP32 Series can be found in Table 1-1 Comparison. MTDI is used to select the VDD_SDIO power supply voltage at reset: • MTDI = 0 (by default), VDD_SDIO pin is powered directly from VDD3P3_RTC. Typically this voltage is 3.3 V. For more information, see Section 2.5.2 Power Scheme. • MTDI = 1, VDD_SDIO pin is powered from internal 1.8 V LDO. This functionality can be overridden by setting EFUSE_SDIO_FORCE to 1, in which case the EFUSE_SDIO_TIEH determines the VDD_SDIO voltage: • EFUSE_SDIO_TIEH = 0, VDD_SDIO connects to 1.8 V LDO. • EFUSE_SDIO_TIEH = 1, VDD_SDIO connects to VDD3P3_RTC. Espressif Systems 24 Submit Documentation Feedback ESP32 Series Datasheet v5.2 3 Boot Configurations 3.3 U0TXD Printing Control During booting, the strapping pin MTDO can be used to control the U0TXD Printing, as Table 3-4 shows. Table 3-4. U0TXD Printing Control U0TXD Printing Control MTDO Enabled 1 1 Disabled 0 1 Bold marks the default value and configuration. 3.4 Timing Control of SDIO Slave The strapping pin MTDO and GPIO5 can be used to control the timing of SDIO slave, see Table 3-5 Timing Control of SDIO Slave. Table 3-5. Timing Control of SDIO Slave Edge behavior MTDO GPIO5 Falling edge sampling, falling edge output 0 0 Falling edge sampling, rising edge output 0 1 Rising edge sampling, falling edge output 1 0 Rising edge sampling, rising edge output 1 1 1 Bold marks the default value and configuration. 3.5 JTAG Signal Source Control If EFUSE_DISABLE_JTAG is set to 1, the source of JTAG signals can be disabled. Espressif Systems 25 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4 Functional Description 4.1 CPU and Memory 4.1.1 CPU ESP32 contains one or two low-power Xtensa ® 32-bit LX6 microprocessor(s) with the following features: • 7-stage pipeline to support the clock frequency of up to 240 MHz (160 MHz for ESP32-S0WD (NRND)) • 16/24-bit Instruction Set provides high code-density • Support for Floating Point Unit • Support for DSP instructions, such as a 32-bit multiplier, a 32-bit divider, and a 40-bit MAC • Support for 32 interrupt vectors from about 70 interrupt sources The single-/dual-CPU interfaces include: • Xtensa RAM/ROM Interface for instructions and data • Xtensa Local Memory Interface for fast peripheral register access • External and internal interrupt sources • JTAG for debugging For information about the Xtensa ® Instruction Set Architecture, please refer to Xtensa ® Instruction Set Architecture (ISA) Summary. 4.1.2 Internal Memory ESP32’s internal memory includes: • 448 KB of ROM for booting and core functions • 520 KB of on-chip SRAM for data and instructions • 8 KB of SRAM in RTC, which is called RTC FAST Memory and can be used for data storage; it is accessed by the main CPU during RTC Boot from the Deep-sleep mode. • 8 KB of SRAM in RTC, which is called RTC SLOW Memory and can be accessed by the ULP coprocessor during the Deep-sleep mode. • 1 Kbit of eFuse: 256 bits are used for the system (MAC address and chip configuration) and the remaining 768 bits are reserved for customer applications, including flash-encryption and chip-ID. • In-package flash or PSRAM Note: Products in the ESP32 series differ from each other, in terms of their support for in-package flash or PSRAM and the size of them. For details, please refer to Section 1 ESP32 Series Comparison. Espressif Systems 26 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.1.3 External Flash and RAM ESP32 supports multiple external QSPI flash and external RAM (SRAM) chips. More details can be found in ESP32 Technical Reference Manual > Chapter SPI Controller. ESP32 also supports hardware encryption/decryption based on AES to protect developers’ programs and data in flash. ESP32 can access the external QSPI flash and SRAM through high-speed caches. • Up to 16 MB of external flash can be mapped into CPU instruction memory space and read-only memory space simultaneously. – When external flash is mapped into CPU instruction memory space, up to 11 MB + 248 KB can be mapped at a time. Note that if more than 3 MB + 248 KB are mapped, cache performance will be reduced due to speculative reads by the CPU. – When external flash is mapped into read-only data memory space, up to 4 MB can be mapped at a time. 8-bit, 16-bit and 32-bit reads are supported. • External RAM can be mapped into CPU data memory space. SRAM up to 8 MB is supported and up to 4 MB can be mapped at a time. 8-bit, 16-bit and 32-bit reads and writes are supported. Note: After ESP32 is initialized, firmware can customize the mapping of external RAM or flash into the CPU address space. 4.1.4 Address Mapping Structure The structure of address mapping is shown in Figure 4-1. The memory and peripheral mapping is shown in Table 4-1. Figure 4-1. Address Mapping Structure Espressif Systems 27 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Table 4-1. Memory and Peripheral Mapping Category Target Start Address End Address Size Embedded Memory Internal ROM 0 0x4000_0000 0x4005_FFFF 384 KB Internal ROM 1 0x3FF9_0000 0x3FF9_FFFF 64 KB Internal SRAM 0 0x4007_0000 0x4009_FFFF 192 KB Internal SRAM 1 0x3FFE_0000 0x3FFF_FFFF 128 KB 0x400A_0000 0x400B_FFFF Internal SRAM 2 0x3FFA_E000 0x3FFD_FFFF 200 KB RTC FAST Memory 0x3FF8_0000 0x3FF8_1FFF 8 KB 0x400C_0000 0x400C_1FFF RTC SLOW Memory 0x5000_0000 0x5000_1FFF 8 KB External Memory External Flash 0x3F40_0000 0x3F7F_FFFF 4 MB 0x400C_2000 0x40BF_FFFF 11 MB+248 KB External RAM 0x3F80_0000 0x3FBF_FFFF 4 MB Peripheral DPort Register 0x3FF0_0000 0x3FF0_0FFF 4 KB AES Accelerator 0x3FF0_1000 0x3FF0_1FFF 4 KB RSA Accelerator 0x3FF0_2000 0x3FF0_2FFF 4 KB SHA Accelerator 0x3FF0_3000 0x3FF0_3FFF 4 KB Secure Boot 0x3FF0_4000 0x3FF0_4FFF 4 KB Cache MMU Table 0x3FF1_0000 0x3FF1_3FFF 16 KB PID Controller 0x3FF1_F000 0x3FF1_FFFF 4 KB UART0 0x3FF4_0000 0x3FF4_0FFF 4 KB SPI1 0x3FF4_2000 0x3FF4_2FFF 4 KB SPI0 0x3FF4_3000 0x3FF4_3FFF 4 KB GPIO 0x3FF4_4000 0x3FF4_4FFF 4 KB RTC 0x3FF4_8000 0x3FF4_8FFF 4 KB IO MUX 0x3FF4_9000 0x3FF4_9FFF 4 KB SDIO Slave 0x3FF4_B000 0x3FF4_BFFF 4 KB UDMA1 0x3FF4_C000 0x3FF4_CFFF 4 KB I2S0 0x3FF4_F000 0x3FF4_FFFF 4 KB UART1 0x3FF5_0000 0x3FF5_0FFF 4 KB I2C0 0x3FF5_3000 0x3FF5_3FFF 4 KB UDMA0 0x3FF5_4000 0x3FF5_4FFF 4 KB SDIO Slave 0x3FF5_5000 0x3FF5_5FFF 4 KB RMT 0x3FF5_6000 0x3FF5_6FFF 4 KB PCNT 0x3FF5_7000 0x3FF5_7FFF 4 KB SDIO Slave 0x3FF5_8000 0x3FF5_8FFF 4 KB LED PWM 0x3FF5_9000 0x3FF5_9FFF 4 KB eFuse Controller 0x3FF5_A000 0x3FF5_AFFF 4 KB Flash Encryption 0x3FF5_B000 0x3FF5_BFFF 4 KB PWM0 0x3FF5_E000 0x3FF5_EFFF 4 KB TIMG0 0x3FF5_F000 0x3FF5_FFFF 4 KB TIMG1 0x3FF6_0000 0x3FF6_0FFF 4 KB SPI2 0x3FF6_4000 0x3FF6_4FFF 4 KB SPI3 0x3FF6_5000 0x3FF6_5FFF 4 KB Espressif Systems 28 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Category Target Start Address End Address Size Peripheral SYSCON 0x3FF6_6000 0x3FF6_6FFF 4 KB I2C1 0x3FF6_7000 0x3FF6_7FFF 4 KB SDMMC 0x3FF6_8000 0x3FF6_8FFF 4 KB EMAC 0x3FF6_9000 0x3FF6_AFFF 8 KB TWAI 0x3FF6_B000 0x3FF6_BFFF 4 KB PWM1 0x3FF6_C000 0x3FF6_CFFF 4 KB I2S1 0x3FF6_D000 0x3FF6_DFFF 4 KB UART2 0x3FF6_E000 0x3FF6_EFFF 4 KB PWM2 0x3FF6_F000 0x3FF6_FFFF 4 KB PWM3 0x3FF7_0000 0x3FF7_0FFF 4 KB RNG 0x3FF7_5000 0x3FF7_5FFF 4 KB 4.1.5 Cache ESP32 uses a two-way set-associative cache. Each of the two CPUs has 32 KB of cache featuring a block size of 32 bytes for accessing external storage. For details, see ESP32 Technical Reference Manual > Chapter System and Memory > Section Cache. 4.2 System Clocks 4.2.1 CPU Clock Upon reset, an external crystal clock source is selected as the default CPU clock. The external crystal clock source also connects to a PLL to generate a high-frequency clock (typically 160 MHz). In addition, ESP32 has an internal 8 MHz oscillator. The application can select the clock source from the external crystal clock source, the PLL clock or the internal 8 MHz oscillator. The selected clock source drives the CPU clock directly, or after division, depending on the application. 4.2.2 RTC Clock The RTC clock has five possible sources: • External low-speed (32 kHz) crystal clock • External crystal clock divided by 4 • Internal RC oscillator (typically about 150 kHz, and adjustable) • Internal 8 MHz oscillator • Internal 31.25 kHz clock (derived from the internal 8 MHz oscillator divided by 256) When the chip is in the normal power mode and needs faster CPU accessing, the application can choose the external high-speed crystal clock divided by 4 or the internal 8 MHz oscillator. When the chip operates in the low-power mode, the application chooses the external low-speed (32 kHz) crystal clock, the internal RC clock or the internal 31.25 kHz clock. Espressif Systems 29 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.2.3 Audio PLL Clock The audio clock is generated by the ultra-low-noise fractional-N PLL. For details, see ESP32 Technical Reference Manual > Chapter Reset and Clock. 4.3 RTC and Low-power Management 4.3.1 Power Management Unit (PMU) With the use of advanced power-management technologies, ESP32 can switch between different power modes. • Power modes – Active mode: The chip radio is powered up. The chip can receive, transmit, or listen. – Modem-sleep mode: The CPU is operational and the clock is configurable. The Wi-Fi/Bluetooth baseband and radio are disabled. – Light-sleep mode: The CPU is paused. The RTC memory and RTC peripherals, as well as the ULP coprocessor are running. Any wake-up events (MAC, SDIO host, RTC timer, or external interrupts) will wake up the chip. – Deep-sleep mode: Only the RTC memory and RTC peripherals are powered up. Wi-Fi and Bluetooth connection data are stored in the RTC memory. The ULP coprocessor is functional. – Hibernation mode: The internal 8 MHz oscillator and ULP coprocessor are disabled. The RTC recovery memory is powered down. Only one RTC timer on the slow clock and certain RTC GPIOs are active. The RTC timer or the RTC GPIOs can wake up the chip from the Hibernation mode. Table 4-2. Power Consumption by Power Modes Power mode Description Power Consumption Active (RF working) Wi-Fi Tx packet Please refer to Table 5-4 for details. Wi-Fi/BT Tx packet Wi-Fi/BT Rx and listening Modem-sleep The CPU is powered up. 240 MHz * Dual-core chip(s) 30 mA ~ 68 mA Single-core chip(s) N/A 160 MHz * Dual-core chip(s) 27 mA ~ 44 mA Single-core chip(s) 27 mA ~ 34 mA Normal speed: 80 MHz Dual-core chip(s) 20 mA ~ 31 mA Single-core chip(s) 20 mA ~ 25 mA Light-sleep - 0.8 mA Deep-sleep The ULP coprocessor is powered up. 150 µA ULP sensor-monitored pattern 100 µA @1% duty RTC timer + RTC memory 10 µA Hibernation RTC timer only 5 µA Power off CHIP_PU is set to low level, the chip is powered down. 1 µA • * Among the ESP32 series of SoCs, ESP32-D0WD-V3, ESP32-D0WDRH2-V3, ESP32-U4WDH, ESP32-D0WD (NRND), ESP32-D0WDQ6 (NRND), and ESP32-D0WDQ6-V3 (NRND) have a maximum CPU frequency of 240 MHz, Espressif Systems 30 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description ESP32-S0WD (NRND) has a maximum CPU frequency of 160 MHz. • When Wi-Fi is enabled, the chip switches between Active and Modem-sleep modes. Therefore, power consumption changes accordingly. • In Modem-sleep mode, the CPU frequency changes automatically. The frequency depends on the CPU load and the peripherals used. • During Deep-sleep, when the ULP coprocessor is powered on, peripherals such as GPIO and RTC I2C are able to operate. • When the system works in the ULP sensor-monitored pattern, the ULP coprocessor works with the ULP sensor periodically and the ADC works with a duty cycle of 1%, so the power consumption is 100 µA. 4.3.2 Ultra-Low-Power Coprocessor The ULP coprocessor and RTC memory remain powered on during the Deep-sleep mode. Hence, the developer can store a program for the ULP coprocessor in the RTC slow memory to access the peripheral devices, internal timers and internal sensors during the Deep-sleep mode. This is useful for designing applications where the CPU needs to be woken up by an external event, or a timer, or a combination of the two, while maintaining minimal power consumption. For details, see ESP32 Technical Reference Manual > Chapter ULP Coprocessor. 4.4 Timers and Watchdogs 4.4.1 General Purpose Timers There are four general-purpose timers embedded in the chip. They are all 64-bit generic timers which are based on 16-bit prescalers and 64-bit auto-reload-capable up/down-timers. The timers feature: • A 16-bit clock prescaler, from 2 to 65536 • A 64-bit timer • Configurable up/down timer: incrementing or decrementing • Halt and resume of time-base counter • Auto-reload at alarming • Software-controlled instant reload • Level and edge interrupt generation For details, see ESP32 Technical Reference Manual > Chapter Timer Group. 4.4.2 Watchdog Timers The chip has three watchdog timers: one in each of the two timer modules (called the Main Watchdog Timer, or MWDT) and one in the RTC module (called the RTC Watchdog Timer, or RWDT). These watchdog timers are intended to recover from an unforeseen fault causing the application program to abandon its normal sequence. A watchdog timer has four stages. Each stage may trigger one of three or four possible actions upon the expiry of its programmed time period, unless the watchdog is fed or disabled. The actions are: interrupt, CPU reset, core Espressif Systems 31 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description reset, and system reset. Only the RWDT can trigger the system reset, and is able to reset the entire chip, including the RTC itself. A timeout value can be set for each stage individually. During flash boot the RWDT and the first MWDT start automatically in order to detect, and recover from, booting problems. The watchdogs have the following features: • Four stages, each of which can be configured or disabled separately • A programmable time period for each stage • One of three or four possible actions (interrupt, CPU reset, core reset, and system reset) upon the expiry of each stage • 32-bit expiry counter • Write protection that prevents the RWDT and MWDT configuration from being inadvertently altered • SPI flash boot protection If the boot process from an SPI flash does not complete within a predetermined time period, the watchdog will reboot the entire system. For details, see ESP32 Technical Reference Manual > Chapter Watchdog Timers. 4.5 Cryptographic Hardware Accelerators ESP32 is equipped with hardware accelerators of general algorithms, such as AES (FIPS PUB 197), SHA (FIPS PUB 180-4), and RSA. The chip also supports independent arithmetic, such as large-number modular multiplication and large-number multiplication. The maximum operation length for RSA, large-number modular multiplication, and large-number multiplication is 4096 bits. The hardware accelerators greatly improve operation speed and reduce software complexity. They also support code encryption and dynamic decryption, which ensures that code in the flash will not be hacked. 4.6 Radio and Wi-Fi The radio module consists of the following blocks: • 2.4 GHz receiver • 2.4 GHz transmitter • Bias and regulators • Balun and transmit-receive switch • Clock generator 4.6.1 2.4 GHz Receiver The 2.4 GHz receiver demodulates the 2.4 GHz RF signal to quadrature baseband signals and converts them to the digital domain with two high-resolution, high-speed ADCs. To adapt to varying signal channel conditions, RF filters, Automatic Gain Control (AGC), DC offset cancelation circuits and baseband filters are integrated in the chip. Espressif Systems 32 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.6.2 2.4 GHz Transmitter The 2.4 GHz transmitter modulates the quadrature baseband signals to the 2.4 GHz RF signal, and drives the antenna with a high-powered Complementary Metal Oxide Semiconductor (CMOS) power amplifier. The use of digital calibration further improves the linearity of the power amplifier, enabling state-of-the-art performance in delivering up to +20.5 dBm of power for an 802.11b transmission and +18 dBm for an 802.11n transmission. Additional calibrations are integrated to cancel any radio imperfections, such as: • Carrier leakage • I/Q phase matching • Baseband nonlinearities • RF nonlinearities • Antenna matching These built-in calibration routines reduce the amount of time required for product testing, and render the testing equipment unnecessary. 4.6.3 Clock Generator The clock generator produces quadrature clock signals of 2.4 GHz for both the receiver and the transmitter. All components of the clock generator are integrated into the chip, including all inductors, varactors, filters, regulators and dividers. The clock generator has built-in calibration and self-test circuits. Quadrature clock phases and phase noise are optimized on-chip with patented calibration algorithms which ensure the best performance of the receiver and the transmitter. 4.6.4 Wi-Fi Radio and Baseband ESP32 implements a TCP/IP and full 802.11 b/g/n Wi-Fi MAC protocol. It supports the Basic Service Set (BSS) STA and SoftAP operations under the Distributed Control Function (DCF). Power management is handled with minimal host interaction to minimize the active-duty period. The ESP32 Wi-Fi Radio and Baseband support the following features: • 802.11b/g/n • 802.11n MCS0-7 in both 20 MHz and 40 MHz bandwidth • 802.11n MCS32 (RX) • 802.11n 0.4 µs guard-interval • up to 150 Mbps of data rate • Receiving STBC 2×1 • Up to 20.5 dBm of transmitting power • Adjustable transmitting power • Antenna diversity ESP32 supports antenna diversity with an external RF switch. One or more GPIOs control the RF switch and selects the best antenna to minimize the effects of channel fading. Espressif Systems 33 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.6.5 Wi-Fi MAC The ESP32 Wi-Fi MAC applies low-level protocol functions automatically. They are as follows: • Four virtual Wi-Fi interfaces • Simultaneous Infrastructure BSS Station mode/SoftAP mode/Promiscuous mode • RTS protection, CTS protection, Immediate Block ACK • Defragmentation • TX/RX A-MPDU, RX A-MSDU • TXOP • WMM • CCMP (CBC-MAC, counter mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4) and CRC • Automatic beacon monitoring (hardware TSF) 4.7 Bluetooth The chip integrates a Bluetooth link controller and Bluetooth baseband, which carry out the baseband protocols and other low-level link routines, such as modulation/demodulation, packet processing, bit stream processing, frequency hopping, etc. 4.7.1 Bluetooth Radio and Baseband The Bluetooth Radio and Baseband support the following features: • Class-1, class-2 and class-3 transmit output powers, and a dynamic control range of up to 21 dB • π/4 DQPSK and 8 DPSK modulation • High performance in NZIF receiver sensitivity with a minimum sensitivity of -94 dBm • Class-1 operation without external PA • Internal SRAM allows full-speed data-transfer, mixed voice and data, and full piconet operation • Logic for forward error correction, header error control, access code correlation, CRC, demodulation, encryption bit stream generation, whitening and transmit pulse shaping • ACL, SCO, eSCO, and AFH • A-law, µ-law, and CVSD digital audio CODEC in PCM interface • SBC audio CODEC • Power management for low-power applications • SMP with 128-bit AES 4.7.2 Bluetooth Interface • Provides UART HCI interface, up to 4 Mbps • Provides SDIO/SPI HCI interface Espressif Systems 34 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description • Provides PCM/I2S audio interface 4.7.3 Bluetooth Stack The Bluetooth stack of the chip is compliant with the Bluetooth v4.2 BR/EDR and Bluetooth LE specifications. 4.7.4 Bluetooth Link Controller The link controller operates in three major states: standby, connection and sniff. It enables multiple connections, and other operations, such as inquiry, page, and secure simple-pairing, and therefore enables Piconet and Scatternet. Below are the features: • Classic Bluetooth – Device Discovery (inquiry, and inquiry scan) – Connection establishment (page, and page scan) – Multi-connections – Asynchronous data reception and transmission – Synchronous links (SCO/eSCO) – Master/Slave Switch – Adaptive Frequency Hopping and Channel assessment – Broadcast encryption – Authentication and encryption – Secure Simple-Pairing – Multi-point and scatternet management – Sniff mode – Connectionless Slave Broadcast (transmitter and receiver) – Enhanced Power Control – Ping • Bluetooth Low Energy – Advertising – Scanning – Simultaneous advertising and scanning – Multiple connections – Asynchronous data reception and transmission – Adaptive Frequency Hopping and Channel assessment – Connection parameter update – Data Length Extension Espressif Systems 35 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description – Link Layer Encryption – LE Ping Espressif Systems 36 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.8 Digital Peripherals 4.8.1 General Purpose Input / Output Interface (GPIO) ESP32 has 34 GPIO pins which can be assigned various functions by programming the appropriate registers. There are several kinds of GPIOs: digital-only, analog-enabled, capacitive-touch-enabled, etc. Analog-enabled GPIOs and Capacitive-touch-enabled GPIOs can be configured as digital GPIOs. Most of the digital GPIOs can be configured as internal pull-up or pull-down, or set to high impedance. When configured as an input, the input value can be read through the register. The input can also be set to edge-trigger or level-trigger to generate CPU interrupts. Most of the digital IO pins are bi-directional, non-inverting and tristate, including input and output buffers with tristate control. These pins can be multiplexed with other functions, such as the SDIO, UART, SPI, etc. (More details can be found in the Appendix, Table IO_MUX. ) For low-power operations, the GPIOs can be set to hold their states. For details, see Section 4.10 Peripheral Pin Configurations, Appendix A –ESP32 Pin Lists and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.2 Serial Peripheral Interface (SPI) ESP32 integrates four SPI controllers which can be used to communicate with external devices that use the SPI protocol. Controller SPI0 is used as a buffer for accessing external memory. Controller SPI1 can be used as a master. Controllers SPI2 and SPI3 can be configured as either a master or a slave. SPI1, SPI2, and SPI3 use signal buses prefixed with SPI, HSPI, and VSPI, respectively. Features of General Purpose SPI (GP-SPI) • Programmable data transfer length, in multiples of 1 byte • Four-line full-duplex/half-duplex communication and three-line half-duplex communication support • Master mode and slave mode • Programmable CPOL and CPHA • Programmable clock For details, see ESP32 Technical Reference Manual > Chapter SPI Controller. Pin Assignment For SPI, the pins are multiplexed with GPIO6 ~ GPIO11 via the IO MUX. For HSPI, the pins are multiplexed with GPIO2, GPIO4, GPIO12 ~ GPIO15 via the IO MUX. For VSPI, the pins are multiplexed with GPIO5, GPIO18 ~ GPIO19, GPIO21 ~ GPIO23 via the IO MUX. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.3 Universal Asynchronous Receiver Transmitter (UART) The UART in the ESP32 chip facilitates the transmission and reception of asynchronous serial data between the chip and external UART devices. It consists of two UARTs in the main system, and one low-power LP UART. Espressif Systems 37 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Feature List • Programmable baud rates up to 5 MBaud • RAM shared by TX FIFOs and RX FIFOs • Supports input baud rate self-check • Support for various lengths of data bits and stop bits • Parity bit support • Asynchronous communication (RS232 and RS485) and IrDA support • Supports DMA to communicate data in high speed • Supports UART wake-up • Supports both software and hardware flow control For details, see ESP32 Technical Reference Manual > Chapter UART Controller. Pin Assignment The pins for UART can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.4 I2C Interface ESP32 has two I2C bus interfaces which can serve as I2C master or slave, depending on the user’s configuration. Feature List • Two I2C controllers: one in the main system and one in the low-power system • Standard mode (100 Kbit/s) • Fast mode (400 Kbit/s) • Up to 5 MHz, yet constrained by SDA pull-up strength • Support for 7-bit and 10-bit addressing, as well as dual address mode • Supports continuous data transmission with disabled Serial Clock Line (SCL) • Supports programmable digital noise filter Users can program command registers to control I2C interfaces, so that they have more flexibility. For details, see ESP32 Technical Reference Manual > Chapter I2C Controller. Pin Assignment For regular I2C, the pins used can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. Espressif Systems 38 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.8.5 I2S Interface The I2S Controller in the ESP32 chip provides a flexible communication interface for streaming digital data in multimedia applications, particularly digital audio applications. Feature List • Master mode and slave mode • Full-duplex and half-duplex communications • A variety of audio standards supported • Configurable high-precision output clock • Supports PDM signal input and output • Configurable data transmit and receive modes For details, see ESP32 Technical Reference Manual > Chapter I2S Controller. Pin Assignment The pins for the I2S Controller can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.6 Remote Control Peripheral The Remote Control Peripheral (RMT) controls the transmission and reception of infrared remote control signals. Feature List • Eight channels for sending and receiving infrared remote control signals • Independent transmission and reception capabilities for each channel • Clock divider counter, state machine, and receiver for each RX channel • Supports various infrared protocols For details, see ESP32 Technical Reference Manual > Chapter Remote Control Peripheral. Pin Assignment The pins for the Remote Control Peripheral can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.7 Pulse Counter Controller (PCNT) The pulse counter controller (PCNT) is designed to count input pulses by tracking rising and falling edges of the input pulse signal. Espressif Systems 39 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Feature List • Eight independent pulse counter units • Each pulse counter unit has a 16-bit signed counter register and two channels • Counter modes: increment, decrement, or disable • Glitch filtering for input pulse signals and control signals • Selection between counting on rising or falling edges of the input pulse signal For details, see ESP32 Technical Reference Manual > Chapter Pulse Count Controller. Pin Assignment The pins for the Pulse Count Controller can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.8 LED PWM Controller The LED PWM Controller (LEDC) is designed to generate PWM signals for LED control. Feature List • Sixteen independent PWM generators • Maximum PWM duty cycle resolution of 20 bits • Eight independent timers with 20-bit counters, configurable fractional clock dividers and counter overflow values • Adjustable phase of PWM signal output • PWM duty cycle dithering • Automatic duty cycle fading For details, see ESP32 Technical Reference Manual > Chapter LED PWM Controller. Pin Assignment The pins for the LED PWM Controller can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.9 Motor Control PWM The Pulse Width Modulation (PWM) controller can be used for driving digital motors and smart lights. The controller consists of PWM timers, the PWM operator and a dedicated capture sub-module. Each timer provides timing in synchronous or independent form, and each PWM operator generates a waveform for one PWM channel. The dedicated capture sub-module can accurately capture events with external timing. Espressif Systems 40 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Feature List • Three PWM timers for precise timing and frequency control – Every PWM timer has a dedicated 8-bit clock prescaler – The 16-bit counter in the PWM timer can work in count-up mode, count-down mode, or count-up-down mode – A hardware sync can trigger a reload on the PWM timer with a phase register. It will also trigger the prescaler’restart, so that the timer’s clock can also be synced, with selectable hardware synchronization source • Three PWM operators for generating waveform pairs – Six PWM outputs to operate in several topologies – Configurable dead time on rising and falling edges; each set up independently – Modulating of PWM output by high-frequency carrier signals, useful when gate drivers are insulated with a transformer • Fault Detection module – Programmable fault handling in both cycle-by-cycle mode and one-shot mode – A fault condition can force the PWM output to either high or low logic levels • Capture module for hardware-based signal processing – Speed measurement of rotating machinery – Measurement of elapsed time between position sensor pulses – Period and duty cycle measurement of pulse train signals – Decoding current or voltage amplitude derived from duty-cycle-encoded signals of current/voltage sensors – Three individual capture channels, each of which with a 32-bit time-stamp register – Selection of edge polarity and prescaling of input capture signals – The capture timer can sync with a PWM timer or external signals For details, see ESP32 Technical Reference Manual > Chapter Motor Control PWM. Pin Assignment The pins for the Motor Control PWM can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.10 SD/SDIO/MMC Host Controller An SD/SDIO/MMC host controller is available on ESP32. Espressif Systems 41 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Feature List • Supports two external cards • Supports SD Memory Card standard: version 3.0 and version 3.01) • Supports SDIO Version 3.0 • Supports Consumer Electronics Advanced Transport Architecture (CE-ATA Version 1.1) • Supports Multimedia Cards (MMC version 4.41, eMMC version 4.5 and version 4.51) The controller allows up to 80 MHz clock output in three different data-bus modes: 1-bit, 4-bit, and 8-bit modes. It supports two SD/SDIO/MMC4.41 cards in a 4-bit data-bus mode. It also supports one SD card operating at 1.8 V. For details, see ESP32 Technical Reference Manual > Chapter SD/MMC Host Controller. Pin Assignment The pins for SD/SDIO/MMC Host Controller are multiplexed with GPIO2, GPIO4, GPIO6 ~ GPIO15 via IO MUX. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.11 SDIO/SPI Slave Controller ESP32 integrates an SD device interface that conforms to the industry-standard SDIO Card Specification Version 2.0, and allows a host controller to access the SoC, using the SDIO bus interface and protocol. ESP32 acts as the slave on the SDIO bus. The host can access the SDIO-interface registers directly and can access shared memory via a DMA engine, thus maximizing performance without engaging the processor cores. Feature List The SDIO/SPI slave controller supports the following features: • SPI, 1-bit SDIO, and 4-bit SDIO transfer modes over the full clock range from 0 to 50 MHz • Configurable sampling and driving clock edge • Special registers for direct access by host • Interrupts to host for initiating data transfer • Automatic loading of SDIO bus data and automatic discarding of padding data • Block size of up to 512 bytes • Interrupt vectors between the host and the slave, allowing both to interrupt each other • Supports DMA for data transfer For details, see ESP32 Technical Reference Manual > Chapter SDIO Slave Controller. Espressif Systems 42 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Pin Assignment The pins for SDIO/SPI Slave Controller are multiplexed with GPIO2, GPIO4, GPIO6 ~ GPIO15 via IO MUX. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.12 TWAI ® Controller The Two-wire Automotive Interface (TWAI ® ) is a multi-master, multi-cast communication protocol designed for automotive applications. The TWAI controller facilitates the communication based on this protocol. Feature List • Compatible with ISO 11898-1 protocol (CAN Specification 2.0) • Standard frame format (11-bit ID) and extended frame format (29-bit ID) • Bit rates: – From 25 Kbit/s to 1 Mbit/s in chip revision v0.0/v1.0/v1.1 – From 12.5 Kbit/s to 1 Mbit/s in chip revision v3.0/v3.1 • Multiple modes of operation: Normal, Listen Only, and Self-Test • 64-byte receive FIFO • Special transmissions: single-shot transmissions and self reception • Acceptance filter (single and dual filter modes) • Error detection and handling: error counters, configurable error interrupt threshold, error code capture, arbitration lost capture For details, see ESP32 Technical Reference Manual > Chapter Two-wire Automotive Interface (TWAI). Pin Assignment The pins for the Two-wire Automotive Interface can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.8.13 Ethernet MAC Interface An IEEE-802.3-2008-compliant Media Access Controller (MAC) is provided for Ethernet LAN communications. ESP32 requires an external physical interface device (PHY) to connect to the physical LAN bus (twisted-pair, fiber, etc.). The PHY is connected to ESP32 through 17 signals of MII or nine signals of RMII. Feature List • 10 Mbps and 100 Mbps rates • Dedicated DMA controller allowing high-speed transfer between the dedicated SRAM and Ethernet MAC • Tagged MAC frame (VLAN support) Espressif Systems 43 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description • Half-duplex (CSMA/CD) and full-duplex operation • MAC control sublayer (control frames) • 32-bit CRC generation and removal • Several address-filtering modes for physical and multicast address (multicast and group addresses) • 32-bit status code for each transmitted or received frame • Internal FIFOs to buffer transmit and receive frames. The transmit FIFO and the receive FIFO are both 512 words (32-bit) • Hardware PTP (Precision Time Protocol) in accordance with IEEE 1588 2008 (PTP V2) • 25 MHz/50 MHz clock output For details, see ESP32 Technical Reference Manual > Chapter Ethernet Media Access Controller (MAC). Pin Assignment For information about the pin assignment of Ethernet MAC Interface, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.9 Analog Peripherals 4.9.1 Analog-to-Digital Converter (ADC) ESP32 integrates two 12-bit SAR ADCs and supports measurements on 18 channels (analog-enabled pins). The ULP coprocessor in ESP32 is also designed to measure voltage, while operating in the sleep mode, which enables low-power consumption. The CPU can be woken up by a threshold setting and/or via other triggers. Table 4-3 describes the ADC characteristics. Table 4-3. ADC Characteristics Parameter Description Min Max Unit DNL (Differential nonlinearity) RTC controller; ADC connected to an –7 7 LSB external 100 nF capacitor; DC signal input; INL (Integral nonlinearity) ambient temperature at 25 °C; –12 12 LSB Wi-Fi&Bluetooth off Sampling rate RTC controller — 200 ksps DIG controller — 2 Msps Notes: • When atten = 3 and the measurement result is above 3000 (voltage at approx. 2450 mV), the ADC accuracy will be worse than described in the table above. • To get better DNL results, users can take multiple sampling tests with a filter, or calculate the average value. • The input voltage range of GPIO pins within VDD3P3_RTC domain should strictly follow the DC characteristics provided in Table 5-3. Otherwise, measurement errors may be introduced, and chip performance may be affected. Espressif Systems 44 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description By default, there are ±6% differences in measured results between chips. ESP-IDF provides couple of calibration methods for ADC1. Results after calibration using eFuse Vref value are shown in Table 4-4. For higher accuracy, users may apply other calibration methods provided in ESP-IDF, or implement their own. Table 4-4. ADC Calibration Results Parameter Description Min Max Unit Total error Atten = 0, effective measurement range of 100 ∼ 950 mV –23 23 mV Atten = 1, effective measurement range of 100 ∼ 1250 mV –30 30 mV Atten = 2, effective measurement range of 150 ∼ 1750 mV –40 40 mV Atten = 3, effective measurement range of 150 ∼ 2450 mV –60 60 mV For details, see ESP32 Technical Reference Manual > Chapter On-Chip Sensors and Analog Signal Processing. Pin Assignment With appropriate settings, the ADCs can be configured to measure voltage on 18 pins maximum. For detailed information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.9.2 Digital-to-Analog Converter (DAC) Two 8-bit DAC channels can be used to convert two digital signals into two analog voltage signal outputs. The design structure is composed of integrated resistor strings and a buffer. This dual DAC supports power supply as input voltage reference. The two DAC channels can also support independent conversions. For details, see ESP32 Technical Reference Manual > Chapter On-Chip Sensors and Analog Signal Processing. Pin Assignment The DAC can be configured by GPIO 25 and GPIO 26. For detailed information about the pin assignment, see Section 4.10 Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 4.9.3 Touch Sensor ESP32 has 10 capacitive-sensing GPIOs, which detect variations induced by touching or approaching the GPIOs with a finger or other objects. The low-noise nature of the design and the high sensitivity of the circuit allow relatively small pads to be used. Arrays of pads can also be used, so that a larger area or more points can be detected. Pin Assignment The 10 capacitive-sensing GPIOs are listed in Table 4-5. Espressif Systems 45 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Table 4-5. Capacitive-Sensing GPIOs Available on ESP32 Capacitive-Sensing Signal Name Pin Name T0 GPIO4 T1 GPIO0 T2 GPIO2 T3 MTDO T4 MTCK T5 MTDI T6 MTMS T7 GPIO27 T8 32K_XN T9 32K_XP For details, see ESP32 Technical Reference Manual > Chapter On-Chip Sensors and Analog Signal Processing. Note: ESP32 Touch Sensor has not passed the Conducted Susceptibility (CS) test for now, and thus has limited application scenarios. Espressif Systems 46 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description 4.10 Peripheral Pin Configurations Table 4-6. Peripheral Pin Configurations Interface Signal Pin Function ADC ADC1_CH0 SENSOR_VP Two 12-bit SAR ADCs ADC1_CH1 SENSOR_CAPP ADC1_CH2 SENSOR_CAPN ADC1_CH3 SENSOR_VN ADC1_CH4 32K_XP ADC1_CH5 32K_XN ADC1_CH6 VDET_1 ADC1_CH7 VDET_2 ADC2_CH0 GPIO4 ADC2_CH1 GPIO0 ADC2_CH2 GPIO2 ADC2_CH3 MTDO ADC2_CH4 MTCK ADC2_CH5 MTDI ADC2_CH6 MTMS ADC2_CH7 GPIO27 ADC2_CH8 GPIO25 ADC2_CH9 GPIO26 DAC DAC_1 GPIO25 Two 8-bit DACs DAC_2 GPIO26 Touch Sensor TOUCH0 GPIO4 Capacitive touch sensors TOUCH1 GPIO0 TOUCH2 GPIO2 TOUCH3 MTDO TOUCH4 MTCK TOUCH5 MTDI TOUCH6 MTMS TOUCH7 GPIO27 TOUCH8 32K_XN TOUCH9 32K_XP JTAG MTDI MTDI JTAG for software debugging MTCK MTCK MTMS MTMS MTDO MTDO Espressif Systems 47 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Interface Signal Pin Function SD/SDIO/MMC Host Controller HS2_CLK MTMS Supports SD memory card V3.01 standard HS2_CMD MTDO HS2_DATA0 GPIO2 HS2_DATA1 GPIO4 HS2_DATA2 MTDI HS2_DATA3 MTCK Motor PWM PWM0_OUT0~2 Any GPIO Pins Three channels of 16-bit timers generate PWM waveforms. Each channel has a pair of output signals, three fault detection signals, three event-capture signals, and three sync signals. PWM1_OUT_IN0~2 PWM0_FLT_IN0~2 PWM1_FLT_IN0~2 PWM0_CAP_IN0~2 PWM1_CAP_IN0~2 PWM0_SYNC_IN0~2 PWM1_SYNC_IN0~2 SDIO/SPI Slave Controller SD_CLK MTMS SDIO interface that conforms to the industry standard SDIO 2.0 card specification SD_CMD MTDO SD_DATA0 GPIO2 SD_DATA1 GPIO4 SD_DATA2 MTDI SD_DATA3 MTCK UART U0RXD_in Any GPIO Pins Three UART devices with hardware flow-control and DMA U0CTS_in U0DSR_in U0TXD_out U0RTS_out U0DTR_out U1RXD_in U1CTS_in U1TXD_out U1RTS_out U2RXD_in U2CTS_in U2TXD_out U2RTS_out I2C I2CEXT0_SCL_in Any GPIO Pins Two I2C devices in slave or master mode I2CEXT0_SDA_in I2CEXT1_SCL_in I2CEXT1_SDA_in I2CEXT0_SCL_out I2CEXT0_SDA_out I2CEXT1_SCL_out I2CEXT1_SDA_out Espressif Systems 48 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Interface Signal Pin Function LED PWM ledc_hs_sig_out0~7 Any GPIO Pins 16 independent channels @80 MHz clock/RTC CLK. Duty accuracy: 16 bits. ledc_ls_sig_out0~7 I2S I2S0I_DATA_in0~15 Any GPIO Pins I2S0O_BCK_in I2S0O_WS_in I2S0I_BCK_in I2S0I_WS_in I2S0I_H_SYNC I2S0I_V_SYNC I2S0I_H_ENABLE I2S0O_BCK_out I2S0O_WS_out Stereo input and output from/to the audio codec; parallel LCD data output; parallel camera data input. I2S0I_BCK_out I2S0I_WS_out I2S0O_DATA_out0~23 I2S1I_DATA_in0~15 I2S1O_BCK_in Note: I2S0_CLK and I2S1_CLK can only be mapped to GPIO0, U0RXD (GPIO3), or U0TXD (GPIO1) via IO MUX by selecting GPIO functions CLK_OUT1, CLK_OUT2, and CLK_OUT3. For more information, see ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix > Table IO MUX Pad Summary. I2S1O_WS_in I2S1I_BCK_in I2S1I_WS_in I2S1I_H_SYNC I2S1I_V_SYNC I2S1I_H_ENABLE I2S1O_BCK_out I2S1O_WS_out I2S1I_BCK_out I2S1I_WS_out I2S1O_DATA_out0~23 I2S0_CLK GPIO0, U0RXD, I2S1_CLK or U0TXD RMT RMT_SIG_IN0~7 Any GPIO Pins Eight channels for an IR transmitter and receiver of various waveformsRMT_SIG_OUT0~7 General Purpose SPI HSPIQ_in/_out Any GPIO Pins Standard SPI consists of clock, chip-select, MOSI and MISO. These SPIs can be connected to LCD and other external devices. They support the following features: • Both master and slave modes; • Four sub-modes of the SPI transfer format; • Configurable SPI frequency; • Up to 64 bytes of FIFO and DMA. HSPID_in/_out HSPICLK_in/_out HSPI_CS0_in/_out HSPI_CS1_out HSPI_CS2_out VSPIQ_in/_out VSPID_in/_out VSPICLK_in/_out VSPI_CS0_in/_out VSPI_CS1_out VSPI_CS2_out Espressif Systems 49 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Interface Signal Pin Function Parallel QSPI SPIHD SD_DATA_2 Supports Standard SPI, Dual SPI, and Quad SPI that can be connected to the external flash and SRAM SPIWP SD_DATA_3 SPICS0 SD_CMD SPICLK SD_CLK SPIQ SD_DATA_0 SPID SD_DATA_1 HSPICLK MTMS HSPICS0 MTDO HSPIQ MTDI HSPID MTCK HSPIHD GPIO4 HSPIWP GPIO2 VSPICLK GPIO18 VSPICS0 GPIO5 VSPIQ GPIO19 VSPID GPIO23 VSPIHD GPIO21 VSPIWP GPIO22 EMAC EMAC_TX_CLK GPIO0 Ethernet MAC with MII/RMII interface EMAC_RX_CLK GPIO5 EMAC_TX_EN GPIO21 EMAC_TXD0 GPIO19 EMAC_TXD1 GPIO22 EMAC_TXD2 MTMS EMAC_TXD3 MTDI EMAC_RX_ER MTCK EMAC_RX_DV GPIO27 EMAC_RXD0 GPIO25 EMAC_RXD1 GPIO26 EMAC_RXD2 U0TXD EMAC_RXD3 MTDO EMAC_CLK_OUT GPIO16 EMAC_CLK_OUT_180 GPIO17 EMAC_TX_ER GPIO4 EMAC_MDC_out Any GPIO Pins EMAC_MDI_in Any GPIO Pins EMAC_MDO_out Any GPIO Pins EMAC_CRS_out Any GPIO Pins EMAC_COL_out Any GPIO Pins Espressif Systems 50 Submit Documentation Feedback ESP32 Series Datasheet v5.2 4 Functional Description Interface Signal Pin Function Pulse Counter pcnt_sig_ch0_in0 Any GPIO Pins Operating in seven different modes, the pulse counter captures pulse and counts pulse edges. pcnt_sig_ch1_in0 pcnt_ctrl_ch0_in0 pcnt_ctrl_ch1_in0 pcnt_sig_ch0_in1 pcnt_sig_ch1_in1 pcnt_ctrl_ch0_in1 pcnt_ctrl_ch1_in1 pcnt_sig_ch0_in2 pcnt_sig_ch1_in2 pcnt_ctrl_ch0_in2 pcnt_ctrl_ch1_in2 pcnt_sig_ch0_in3 pcnt_sig_ch1_in3 pcnt_ctrl_ch0_in3 pcnt_ctrl_ch1_in3 pcnt_sig_ch0_in4 pcnt_sig_ch1_in4 pcnt_ctrl_ch0_in4 pcnt_ctrl_ch1_in4 pcnt_sig_ch0_in5 pcnt_sig_ch1_in5 pcnt_ctrl_ch0_in5 pcnt_ctrl_ch1_in5 pcnt_sig_ch0_in6 pcnt_sig_ch1_in6 pcnt_ctrl_ch0_in6 pcnt_ctrl_ch1_in6 pcnt_sig_ch0_in7 pcnt_sig_ch1_in7 pcnt_ctrl_ch0_in7 pcnt_ctrl_ch1_in7 TWAI twai_rx Any GPIO Pins Compatible with ISO 11898-1 protocol (CAN Specification 2.0) twai_tx twai_bus_off_on twai_clkout Espressif Systems 51 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics 5 Electrical Characteristics 5.1 Absolute Maximum Ratings Stresses above those listed in Table 5-1 Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and normal operation of the device at these or any other conditions beyond those indicated in Section 5.2 Recommended Power Supply Characteristics is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Table 5-1. Absolute Maximum Ratings Parameter Description Min Max Unit VDDA, VDD3P3, VDD3P3_RTC, VDD3P3_CPU, VDD_SDIO Allowed input voltage –0.3 3.6 V I output 1 Cumulative IO output current — 1200 mA T ST ORE Storage temperature –40 150 °C 1 The product proved to be fully functional after all its IO pins were pulled high while being connected to ground for 24 consecutive hours at ambient temperature of 25 °C. 5.2 Recommended Power Supply Characteristics Table 5-2. Recommended Power Supply Characteristics Parameter Description Min Typ Max Unit VDDA, VDD3P3_RTC, VDD3P3, VDD_SDIO (3.3 V mode) note 1 Voltage applied to power supply pins per power domain 2.3/3.0 note 2 3.3 3.6 V VDD3P3_CPU Voltage applied to power supply pin 1.8 3.3 3.6 V I V DD Current delivered by external power supply 0.5 — — A T note 3 Operating temperature –40 — 125 °C 1. • VDD_SDIO works as the power supply for the related IO, and also for an external device. Please refer to the Appendix IO_MUX of this datasheet for more details. • VDD_SDIO can be sourced internally by the ESP32 from the VDD3P3_RTC power domain: – When VDD_SDIO operates at 3.3 V, it is driven directly by VDD3P3_RTC through a 6 Ω resistor, therefore, there will be some voltage drop from VDD3P3_RTC. – When VDD_SDIO operates at 1.8 V, it can be generated from ESP32’s internal LDO. The maximum current this LDO can offer is 40 mA, and the output voltage range is 1.65 V ~ 2.0 V. • VDD_SDIO can also be driven by an external power supply. • Please refer to Section 2.5.2 Power Scheme, for more information. 2. • Chips with a 3.3 V flash or PSRAM in-package: this minimum voltage is 3.0 V; • Chips with no flash or PSRAM in-package: this minimum voltage is 2.3 V; • For more information, see Section 1 ESP32 Series Comparison. 3. The operating temperature of ESP32-U4WDH and ESP32-D0WDRH2-V3 ranges from –40 °C to 85 °C, due to the in-package flash or PSRAM. For other chips that have no in-package flash or PSRAM, their operating temperature is – 40 °C ~ 125 °C. Espressif Systems 52 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics 5.3 DC Characteristics (3.3 V, 25 °C) Table 5-3. DC Characteristics (3.3 V, 25 °C) Parameter Description Min Typ Max Unit C IN Pin capacitance — 2 — pF V IH High-level input voltage 0.75 × VDD 1 — VDD 1 + 0.3 V V IL Low-level input voltage –0.3 — 0.25 × VDD 1 V I IH High-level input current — — 50 nA I IL Low-level input current — — 50 nA V OH High-level output voltage 0.8 × VDD 1 — — V V OL Low-level output voltage — — 0.1 × VDD 1 V I OH High-level source current (VDD 1 = 3.3 V, V OH >= 2.64 V, output drive strength set to the maximum) VDD3P3_CPU power domain 1, 2 — 40 — mA VDD3P3_RTC power domain 1, 2 — 40 — mA VDD_SDIO power domain 1, 3 — 20 — mA I OL Low-level sink current (VDD 1 = 3.3 V, V OL = 0.495 V, output drive strength set to the maximum) — 28 — mA R P U Resistance of internal pull-up resistor — 45 — kΩ R P D Resistance of internal pull-down resistor — 45 — kΩ V IH _nRST Chip reset release voltage (CHIP_PU voltage is within the specified range) 0.75 × VDD 1 — VDD 1 + 0.3 V V IL _nRST Low-level input voltage of CHIP_PU to shut down the chip — — 0.6 V 1. Please see Table IO_MUX for IO’s power domain. VDD is the I/O voltage for a particular power domain of pins. 2. For VDD3P3_CPU and VDD3P3_RTC power domain, per-pin current sourced in the same domain is gradually reduced from around 40 mA to around 29 mA, V OH >=2.64 V, as the number of current-source pins increases. 3. For VDD_SDIO power domain, per-pin current sourced in the same domain is gradually reduced from around 30 mA to around 10 mA, V OH >=2.64 V, as the number of current-source pins increases. 5.4 RF Current Consumption in Active Mode The current consumption measurements are taken with a 3.3 V supply at 25 °C of ambient temperature at the RF port. All transmitters’ measurements are based on a 50% duty cycle. Table 5-4. Current Consumption Depending on RF Modes Work Mode Min Typ Max Unit Transmit 802.11b, DSSS 1 Mbps, POUT = +19.5 dBm — 240 — mA Transmit 802.11g, OFDM 54 Mbps, POUT = +16 dBm — 190 — mA Transmit 802.11n, OFDM MCS7, POUT = +14 dBm — 180 — mA Receive 802.11b/g/n — 95 ~ 100 — mA Espressif Systems 53 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics Work Mode Min Typ Max Unit Transmit BT/BLE, POUT = 0 dBm — 130 — mA Receive BT/BLE — 95 ~ 100 — mA 5.5 Reliability Table 5-5. Reliability Qualifications Test Item Test Conditions Test Standard HTOL (High Temperature Operating Life) 125 °C, 1000 hours JESD22-A108 ESD (Electro-Static Discharge Sensitivity) HBM (Human Body Mode) 1 ± 2000 V JS-001 CDM (Charge Device Mode) 2 ± 500 V JS-002 Latch up Current trigger ± 200 mA JESD78 Voltage trigger 1.5 × VDD max Preconditioning Bake 24 hours @125 °C Moisture soak (level 3: 192 hours @30 °C, 60% RH) IR reflow solder: 260 + 0 °C, 20 seconds, three times J-STD-020, JESD47, JESD22-A113 TCT (Temperature Cycling Test) –65 °C / 150 °C, 500 cycles JESD22-A104 Autoclave Test 121 °C, 100% RH, 96 hours JESD22-A102 uHAST (Highly Acceler- ated Stress Test, unbiased) 130 °C, 85% RH, 96 hours JESD22-A118 HTSL (High Temperature Storage Life) 150 °C, 1000 hours JESD22-A103 1. JEDEC document JEP155 states that 500 V HBM allows safe manufacturing with a standard ESD control process. 2. JEDEC document JEP157 states that 250 V CDM allows safe manufacturing with a standard ESD control process. 5.6 Wi-Fi Radio Table 5-6. Wi-Fi Radio Characteristics Parameter Description Min Typ Max Unit Operating frequency range note1 — 2412 — 2484 MHz Output impedance note2 - - note 2 — Ω TX power note3 11n, MCS7 12 13 14 dBm 11b mode 18.5 19.5 20.5 dBm Sensitivity 11b, 1 Mbps — –98 — dBm 11b, 11 Mbps — –88 — dBm 11g, 6 Mbps — –93 — dBm 11g, 54 Mbps — –75 — dBm 11n, HT20, MCS0 — –93 — dBm 11n, HT20, MCS7 — –73 — dBm Espressif Systems 54 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics Parameter Description Min Typ Max Unit 11n, HT40, MCS0 — –90 — dBm 11n, HT40, MCS7 — –70 — dBm Adjacent channel rejection 11g, 6 Mbps — 27 — dB 11g, 54 Mbps — 13 — dB 11n, HT20, MCS0 — 27 — dB 11n, HT20, MCS7 — 12 — dB 1. Device should operate in the frequency range allocated by regional regulatory authorities. Target operating frequency range is configurable by software. 2. The typical value of the Wi-Fi radio output impedance is different between chips in different QFN packages. For chips in a QFN 6×6 package, the value is 30+j10 Ω. For chips in a QFN 5×5 package, the value is 35+j10 Ω. 3. Target TX power is configurable based on device or certification requirements. 5.7 Bluetooth Radio 5.7.1 Receiver –Basic Data Rate Table 5-7. Receiver Characteristics –Basic Data Rate Parameter Description Min Typ Max Unit Sensitivity @0.1% BER — –90 –89 –88 dBm Maximum received signal @0.1% BER — 0 — — dBm Co-channel C/I — — +7 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — — –6 dB F = F0 –1 MHz — — –6 dB F = F0 + 2 MHz — — –25 dB F = F0 –2 MHz — — –33 dB F = F0 + 3 MHz — — –25 dB F = F0 –3 MHz — — –45 dB Out-of-band blocking performance 30 MHz ~ 2000 MHz –10 — — dBm 2000 MHz ~ 2400 MHz –27 — — dBm 2500 MHz ~ 3000 MHz –27 — — dBm 3000 MHz ~ 12.5 GHz –10 — — dBm Intermodulation — –36 — — dBm 5.7.2 Transmitter –Basic Data Rate Table 5-8. Transmitter Characteristics –Basic Data Rate Parameter Description Min Typ Max Unit RF transmit power note1 — — 0 — dBm Gain control step — — 3 — dB RF power control range — –12 — +9 dBm +20 dB bandwidth — — 0.9 — MHz Espressif Systems 55 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics Parameter Description Min Typ Max Unit Adjacent channel transmit power F = F0 ± 2 MHz — –47 — dBm F = F0 ± 3 MHz — –55 — dBm F = F0 ± > 3 MHz — –60 — dBm ∆ f1 avg — — — 155 kHz ∆ f2 max — 133.7 — — kHz ∆ f2 avg /∆ f1 avg — — 0.92 — — ICFT — — –7 — kHz Drift rate — — 0.7 — kHz/50 µ s Drift (DH1) — — 6 — kHz Drift (DH5) — — 6 — kHz 1. There are in total eight power levels from level 0 to level 7, with transmit power ranging from –12 dBm to 9 dBm. When the power level rises by 1, the transmit power increases by 3 dB. Power level 4 is used by default and the corresponding transmit power is 0 dBm. 5.7.3 Receiver –Enhanced Data Rate Table 5-9. Receiver Characteristics –Enhanced Data Rate Parameter Description Min Typ Max Unit π/4 DQPSK Sensitivity @0.01% BER — –90 –89 –88 dBm Maximum received signal @0.01% BER — — 0 — dBm Co-channel C/I — — 11 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — –7 — dB F = F0 –1 MHz — –7 — dB F = F0 + 2 MHz — –25 — dB F = F0 –2 MHz — –35 — dB F = F0 + 3 MHz — –25 — dB F = F0 –3 MHz — –45 — dB 8DPSK Sensitivity @0.01% BER — –84 –83 –82 dBm Maximum received signal @0.01% BER — — –5 — dBm C/I c-channel — — 18 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — 2 — dB F = F0 –1 MHz — 2 — dB F = F0 + 2 MHz — –25 — dB F = F0 –2 MHz — –25 — dB F = F0 + 3 MHz — –25 — dB F = F0 –3 MHz — –38 — dB 5.7.4 Transmitter –Enhanced Data Rate Espressif Systems 56 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics Table 5-10. Transmitter Characteristics –Enhanced Data Rate Parameter Description Min Typ Max Unit RF transmit power (see note under Table 5-10) — — 0 — dBm Gain control step — — 3 — dB RF power control range — –12 — +9 dBm π/4 DQPSK max w0 — — –0.72 — kHz π/4 DQPSK max wi — — –6 — kHz π/4 DQPSK max |wi + w0| — — –7.42 — kHz 8DPSK max w0 — — 0.7 — kHz 8DPSK max wi — — –9.6 — kHz 8DPSK max |wi + w0| — — –10 — kHz π/4 DQPSK modulation accuracy RMS DEVM — 4.28 — % 99% DEVM — 100 — % Peak DEVM — 13.3 — % 8 DPSK modulation accuracy RMS DEVM — 5.8 — % 99% DEVM — 100 — % Peak DEVM — 14 — % In-band spurious emissions F = F0 ± 1 MHz — –46 — dBm F = F0 ± 2 MHz — –40 — dBm F = F0 ± 3 MHz — –46 — dBm F = F0 +/–> 3 MHz — — –53 dBm EDR differential phase coding — — 100 — % 5.8 Bluetooth LE Radio 5.8.1 Receiver Table 5-11. Receiver Characteristics –Bluetooth LE Parameter Description Min Typ Max Unit Sensitivity @30.8% PER — –94 –93 –92 dBm Maximum received signal @30.8% PER — 0 — — dBm Co-channel C/I — — +10 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — –5 — dB F = F0 –1 MHz — –5 — dB F = F0 + 2 MHz — –25 — dB F = F0 –2 MHz — –35 — dB F = F0 + 3 MHz — –25 — dB F = F0 –3 MHz — –45 — dB Out-of-band blocking performance 30 MHz ~ 2000 MHz –10 — — dBm 2000 MHz ~ 2400 MHz –27 — — dBm 2500 MHz ~ 3000 MHz –27 — — dBm 3000 MHz ~ 12.5 GHz –10 — — dBm Intermodulation — –36 — — dBm Espressif Systems 57 Submit Documentation Feedback ESP32 Series Datasheet v5.2 5 Electrical Characteristics 5.8.2 Transmitter Table 5-12. Transmitter Characteristics –Bluetooth LE Parameter Description Min Typ Max Unit RF transmit power (see note under Table 5-8) — — 0 — dBm Gain control step — — 3 — dB RF power control range — –12 — +9 dBm Adjacent channel transmit power F = F0 ± 2 MHz — –52 — dBm F = F0 ± 3 MHz — –58 — dBm F = F0 ± > 3 MHz — –60 — dBm ∆ f1 avg — — — 265 kHz ∆ f2 max — 247 — — kHz ∆ f2 avg /∆ f1 avg — — 0.92 — — ICFT — — –10 — kHz Drift rate — — 0.7 — kHz/50 µs Drift — — 2 — kHz Espressif Systems 58 Submit Documentation Feedback ESP32 Series Datasheet v5.2 6 Packaging 6 Packaging • For information about tape, reel, and chip marking, please refer to ESP32 Chip Packaging Information. • The pins of the chip are numbered in anti-clockwise order starting from Pin 1 in the top view. For pin numbers and pin names, see also pin layout figures in Section 2.1 Pin Layout. Pin 1 Pin 2 Pin 3 Pin 1 Pin 2 Pin 3 Figure 6-1. QFN48 (6x6 mm) Package D    L   L 48L SLP L E e_f (5x5r1r1) 0 a.a.a. C 0 a.a.a. C TOP VIEw  SIDE VIEw D2 + bl 48X     E2                rn                                    BOTTOM VIEw   CCC  ddd      Notes                 in   n  Figure 6-2. QFN48 (5x5 mm) Package Espressif Systems 59 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Related Documentation and Resources Related Documentation and Resources Related Documentation • ESP32 Technical Reference Manual – Detailed information on how to use the ESP32 memory and peripherals. • ESP32 Hardware Design Guidelines – Guidelines on how to integrate the ESP32 into your hardware product. • ESP32 ECO and Workarounds for Bugs – Correction of ESP32 design errors. • ESP32 Series SoC Errata – Descriptions of known errors in ESP32 series of SoCs. • Certificates https://espressif.com/en/support/documents/certificates • ESP32 Product/Process Change Notifications (PCN) https://espressif.com/en/support/documents/pcns • ESP32 Advisories – Information on security, bugs, compatibility, component reliability. https://espressif.com/en/support/documents/advisories • Documentation Updates and Update Notification Subscription https://espressif.com/en/support/download/documents Developer Zone • ESP-IDF Programming Guide for ESP32 – Extensive documentation for the ESP-IDF development framework. • ESP-IDF and other development frameworks on GitHub. https://github.com/espressif • ESP32 BBS Forum – Engineer-to-Engineer (E2E) Community for Espressif products where you can post questions, share knowledge, explore ideas, and help solve problems with fellow engineers. https://esp32.com/ • The ESP Journal – Best Practices, Articles, and Notes from Espressif folks. https://blog.espressif.com/ • See the tabs SDKs and Demos, Apps, Tools, AT Firmware. https://espressif.com/en/support/download/sdks-demos Products • ESP32 Series SoCs – Browse through all ESP32 SoCs. https://espressif.com/en/products/socs?id=ESP32 • ESP32 Series Modules – Browse through all ESP32-based modules. https://espressif.com/en/products/modules?id=ESP32 • ESP32 Series DevKits – Browse through all ESP32-based devkits. https://espressif.com/en/products/devkits?id=ESP32 • ESP Product Selector – Find an Espressif hardware product suitable for your needs by comparing or applying filters. https://products.espressif.com/#/product-selector?language=en Contact Us • See the tabs Sales Questions, Technical Enquiries, Circuit Schematic & PCB Design Review, Get Samples (Online stores), Become Our Supplier, Comments & Suggestions. https://espressif.com/en/contact-us/sales-questions Espressif Systems 60 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A Appendix A –ESP32 Pin Lists A.1. Notes on ESP32 Pin Lists Table 6-1. Notes on ESP32 Pin Lists No. Description 1 In Table IO_MUX, the boxes highlighted in yellow indicate the GPIO pins that are input-only. Please see the following note for further details. 2 GPIO pins 34-39 are input-only. These pins do not feature an output driver or internal pull- up/pull-down circuitry. The pin names are: SENSOR_VP (GPIO36), SENSOR_CAPP (GPIO37), SENSOR_CAPN (GPIO38), SENSOR_VN (GPIO39), VDET_1 (GPIO34), VDET_2 (GPIO35). 3 The pins are grouped into four power domains: VDDA (analog power supply), VDD3P3_RTC (RTC power supply), VDD3P3_CPU (power supply of digital IOs and CPU cores), VDD_SDIO (power supply of SDIO IOs). VDD_SDIO is the output of the internal SDIO-LDO. The voltage of SDIO-LDO can be configured at 1.8 V or be the same as that of VDD3P3_RTC. The strap- ping pin and eFuse bits determine the default voltage of the SDIO-LDO. Software can change the voltage of the SDIO-LDO by configuring register bits. For details, please see the column “Power Domain”in Table IO_MUX. 4 The functional pins in the VDD3P3_RTC domain are those with analog functions, including the 32 kHz crystal oscillator, ADC, DAC, and the capacitive touch sensor. Please see columns “Analog Function 0 ~ 2” in Table IO_MUX. 5 These VDD3P3_RTC pins support the RTC function, and can work during Deep-sleep. For example, an RTC-GPIO can be used for waking up the chip from Deep-sleep. 6 The GPIO pins support up to six digital functions, as shown in columns “Function 0 ~ 5” In Table IO_MUX. The function selection registers will be set as “N”, where N is the function number. Below are some definitions: • SD_* is for signals of the SDIO slave. • HS1_* is for Port 1 signals of the SDIO host. • HS2_* is for Port 2 signals of the SDIO host. • MT* is for signals of the JTAG. • U0* is for signals of the UART0 module. • U1* is for signals of the UART1 module. • U2* is for signals of the UART2 module. • SPI* is for signals of the SPI01 module. • HSPI* is for signals of the SPI2 module. • VSPI* is for signals of the SPI3 module. Espressif Systems 61 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A No. Description 7 Each column about digital“Function” is accompanied by a column about“Type”. Please see the following explanations for the meanings of “type” with respect to each “function” they are associated with. For each “Function-N”, “type” signifies: • I: input only. If a function other than “Function-N” is assigned, the input signal of “Function-N” is still from this pin. • I1: input only. If a function other than “Function-N” is assigned, the input signal of “Function-N” is always “1”. • I0: input only. If a function other than “Function-N” is assigned, the input signal of “Function-N” is always “0”. • O: output only. • T: high-impedance. • I/O/T: combinations of input, output, and high-impedance according to the function sig- nal. • I1/O/T: combinations of input, output, and high-impedance, according to the function signal. If a function is not selected, the input signal of the function is “1”. For example, pin 30 can function as HS1_CMD or SD_CMD, where HS1_CMD is of an“I1/O/T” type. If pin 30 is selected as HS1_CMD, this pin’s input and output are controlled by the SDIO host. If pin 30 is not selected as HS1_CMD, the input signal of the SDIO host is always “1”. 8 Each digital output pin is associated with its configurable drive strength. Column “Drive Strength” in Table IO_MUX lists the default values. The drive strength of the digital output pins can be configured into one of the following four options: • 0: ~5 mA • 1: ~10 mA • 2: ~20 mA • 3: ~40 mA The default value is 2. The drive strength of the internal pull-up (wpu) and pull-down (wpd) is ~75 µA. 9 Column “At Reset” in Table IO_MUX lists the status of each pin during reset, including input- enable (ie=1), internal pull-up (wpu) and internal pull-down (wpd). During reset, all pins are output-disabled. 10 Column “After Reset” in Table IO_MUX lists the status of each pin immediately after reset, including input-enable (ie=1), internal pull-up (wpu) and internal pull-down (wpd). After reset, each pin is set to “Function 0”. The output-enable is controlled by digital Function 0. 11 Table Ethernet_MAC is about the signal mapping inside Ethernet MAC. The Ethernet MAC supports MII and RMII interfaces, and supports both the internal PLL clock and the external clock source. For the MII interface, the Ethernet MAC is with/without the TX_ERR signal. MDC, MDIO, CRS and COL are slow signals, and can be mapped onto any GPIO pin through the GPIO-Matrix. 12 Table GPIO Matrix is for the GPIO-Matrix. The signals of the on-chip functional modules can be mapped onto any GPIO pin. Some signals can be mapped onto a pin by both IO-MUX and GPIO-Matrix, as shown in the column tagged as “Same input signal from IO_MUX core” in Table GPIO Matrix. Espressif Systems 62 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A No. Description 13 *In Table GPIO_Matrix，the column “Default Value if unassigned”records the default value of the an input signal if no GPIO is assigned to it. The actual value is determined by register GPIO_FUNCm_IN_INV_SEL and GPIO_FUNCm_IN_SEL. (The value of m ranges from 1 to 255.) A.2. GPIO_Matrix Table 6-2. GPIO_Matrix Signal No. Input Signals Default Value If Unassigned* Same Input Sig- nal from IO_MUX Core Output Signals Output Enable of Output Signals 0 SPICLK_in 0 yes SPICLK_out SPICLK_oe 1 SPIQ_in 0 yes SPIQ_out SPIQ_oe 2 SPID_in 0 yes SPID_out SPID_oe 3 SPIHD_in 0 yes SPIHD_out SPIHD_oe 4 SPIWP_in 0 yes SPIWP_out SPIWP_oe 5 SPICS0_in 0 yes SPICS0_out SPICS0_oe 6 SPICS1_in 0 no SPICS1_out SPICS1_oe 7 SPICS2_in 0 no SPICS2_out SPICS2_oe 8 HSPICLK_in 0 yes HSPICLK_out HSPICLK_oe 9 HSPIQ_in 0 yes HSPIQ_out HSPIQ_oe 10 HSPID_in 0 yes HSPID_out HSPID_oe 11 HSPICS0_in 0 yes HSPICS0_out HSPICS0_oe 12 HSPIHD_in 0 yes HSPIHD_out HSPIHD_oe 13 HSPIWP_in 0 yes HSPIWP_out HSPIWP_oe 14 U0RXD_in 0 yes U0TXD_out 1’d1 15 U0CTS_in 0 yes U0RTS_out 1’d1 16 U0DSR_in 0 no U0DTR_out 1’d1 17 U1RXD_in 0 yes U1TXD_out 1’d1 18 U1CTS_in 0 yes U1RTS_out 1’d1 23 I2S0O_BCK_in 0 no I2S0O_BCK_out 1’d1 24 I2S1O_BCK_in 0 no I2S1O_BCK_out 1’d1 25 I2S0O_WS_in 0 no I2S0O_WS_out 1’d1 26 I2S1O_WS_in 0 no I2S1O_WS_out 1’d1 27 I2S0I_BCK_in 0 no I2S0I_BCK_out 1’d1 28 I2S0I_WS_in 0 no I2S0I_WS_out 1’d1 29 I2CEXT0_SCL_in 1 no I2CEXT0_SCL_out 1’d1 30 I2CEXT0_SDA_in 1 no I2CEXT0_SDA_out 1’d1 31 pwm0_sync0_in 0 no sdio_tohost_int_out 1’d1 32 pwm0_sync1_in 0 no pwm0_out0a 1’d1 33 pwm0_sync2_in 0 no pwm0_out0b 1’d1 Espressif Systems 63 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A Signal No. Input Signals Default Value If Unassigned* Same Input Sig- nal from IO_MUX Core Output Signals Output Enable of Output Signals 34 pwm0_f0_in 0 no pwm0_out1a 1’d1 35 pwm0_f1_in 0 no pwm0_out1b 1’d1 36 pwm0_f2_in 0 no pwm0_out2a 1’d1 37 — 0 no pwm0_out2b 1’d1 39 pcnt_sig_ch0_in0 0 no — 1’d1 40 pcnt_sig_ch1_in0 0 no — 1’d1 41 pcnt_ctrl_ch0_in0 0 no — 1’d1 42 pcnt_ctrl_ch1_in0 0 no — 1’d1 43 pcnt_sig_ch0_in1 0 no — 1’d1 44 pcnt_sig_ch1_in1 0 no — 1’d1 45 pcnt_ctrl_ch0_in1 0 no — 1’d1 46 pcnt_ctrl_ch1_in1 0 no — 1’d1 47 pcnt_sig_ch0_in2 0 no — 1’d1 48 pcnt_sig_ch1_in2 0 no — 1’d1 49 pcnt_ctrl_ch0_in2 0 no — 1’d1 50 pcnt_ctrl_ch1_in2 0 no — 1’d1 51 pcnt_sig_ch0_in3 0 no — 1’d1 52 pcnt_sig_ch1_in3 0 no — 1’d1 53 pcnt_ctrl_ch0_in3 0 no — 1’d1 54 pcnt_ctrl_ch1_in3 0 no — 1’d1 55 pcnt_sig_ch0_in4 0 no — 1’d1 56 pcnt_sig_ch1_in4 0 no — 1’d1 57 pcnt_ctrl_ch0_in4 0 no — 1’d1 58 pcnt_ctrl_ch1_in4 0 no — 1’d1 61 HSPICS1_in 0 no HSPICS1_out HSPICS1_oe 62 HSPICS2_in 0 no HSPICS2_out HSPICS2_oe 63 VSPICLK_in 0 yes VSPICLK_out_mux VSPICLK_oe 64 VSPIQ_in 0 yes VSPIQ_out VSPIQ_oe 65 VSPID_in 0 yes VSPID_out VSPID_oe 66 VSPIHD_in 0 yes VSPIHD_out VSPIHD_oe 67 VSPIWP_in 0 yes VSPIWP_out VSPIWP_oe 68 VSPICS0_in 0 yes VSPICS0_out VSPICS0_oe 69 VSPICS1_in 0 no VSPICS1_out VSPICS1_oe 70 VSPICS2_in 0 no VSPICS2_out VSPICS2_oe 71 pcnt_sig_ch0_in5 0 no ledc_hs_sig_out0 1’d1 72 pcnt_sig_ch1_in5 0 no ledc_hs_sig_out1 1’d1 73 pcnt_ctrl_ch0_in5 0 no ledc_hs_sig_out2 1’d1 74 pcnt_ctrl_ch1_in5 0 no ledc_hs_sig_out3 1’d1 75 pcnt_sig_ch0_in6 0 no ledc_hs_sig_out4 1’d1 76 pcnt_sig_ch1_in6 0 no ledc_hs_sig_out5 1’d1 Espressif Systems 64 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A Signal No. Input Signals Default Value If Unassigned* Same Input Sig- nal from IO_MUX Core Output Signals Output Enable of Output Signals 77 pcnt_ctrl_ch0_in6 0 no ledc_hs_sig_out6 1’d1 78 pcnt_ctrl_ch1_in6 0 no ledc_hs_sig_out7 1’d1 79 pcnt_sig_ch0_in7 0 no ledc_ls_sig_out0 1’d1 80 pcnt_sig_ch1_in7 0 no ledc_ls_sig_out1 1’d1 81 pcnt_ctrl_ch0_in7 0 no ledc_ls_sig_out2 1’d1 82 pcnt_ctrl_ch1_in7 0 no ledc_ls_sig_out3 1’d1 83 rmt_sig_in0 0 no ledc_ls_sig_out4 1’d1 84 rmt_sig_in1 0 no ledc_ls_sig_out5 1’d1 85 rmt_sig_in2 0 no ledc_ls_sig_out6 1’d1 86 rmt_sig_in3 0 no ledc_ls_sig_out7 1’d1 87 rmt_sig_in4 0 no rmt_sig_out0 1’d1 88 rmt_sig_in5 0 no rmt_sig_out1 1’d1 89 rmt_sig_in6 0 no rmt_sig_out2 1’d1 90 rmt_sig_in7 0 no rmt_sig_out3 1’d1 91 — — — rmt_sig_out4 1’d1 92 — — — rmt_sig_out6 1’d1 94 twai_rx 1 no rmt_sig_out7 1’d1 95 I2CEXT1_SCL_in 1 no I2CEXT1_SCL_out 1’d1 96 I2CEXT1_SDA_in 1 no I2CEXT1_SDA_out 1’d1 97 host_card_detect_n_1 0 no host_ccmd_od_pullup_en_n 1’d1 98 host_card_detect_n_2 0 no host_rst_n_1 1’d1 99 host_card_write_prt_1 0 no host_rst_n_2 1’d1 100 host_card_write_prt_2 0 no gpio_sd0_out 1’d1 101 host_card_int_n_1 0 no gpio_sd1_out 1’d1 102 host_card_int_n_2 0 no gpio_sd2_out 1’d1 103 pwm1_sync0_in 0 no gpio_sd3_out 1’d1 104 pwm1_sync1_in 0 no gpio_sd4_out 1’d1 105 pwm1_sync2_in 0 no gpio_sd5_out 1’d1 106 pwm1_f0_in 0 no gpio_sd6_out 1’d1 107 pwm1_f1_in 0 no gpio_sd7_out 1’d1 108 pwm1_f2_in 0 no pwm1_out0a 1’d1 109 pwm0_cap0_in 0 no pwm1_out0b 1’d1 110 pwm0_cap1_in 0 no pwm1_out1a 1’d1 111 pwm0_cap2_in 0 no pwm1_out1b 1’d1 112 pwm1_cap0_in 0 no pwm1_out2a 1’d1 113 pwm1_cap1_in 0 no pwm1_out2b 1’d1 114 pwm1_cap2_in 0 no pwm2_out1h 1’d1 115 pwm2_flta 1 no pwm2_out1l 1’d1 116 pwm2_fltb 1 no pwm2_out2h 1’d1 117 pwm2_cap1_in 0 no pwm2_out2l 1’d1 Espressif Systems 65 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A Signal No. Input Signals Default Value If Unassigned* Same Input Sig- nal from IO_MUX Core Output Signals Output Enable of Output Signals 118 pwm2_cap2_in 0 no pwm2_out3h 1’d1 119 pwm2_cap3_in 0 no pwm2_out3l 1’d1 120 pwm3_flta 1 no pwm2_out4h 1’d1 121 pwm3_fltb 1 no pwm2_out4l 1’d1 122 pwm3_cap1_in 0 no — 1’d1 123 pwm3_cap2_in 0 no twai_tx 1’d1 124 pwm3_cap3_in 0 no twai_bus_off_on 1’d1 125 — — — twai_clkout 1’d1 140 I2S0I_DATA_in0 0 no I2S0O_DATA_out0 1’d1 141 I2S0I_DATA_in1 0 no I2S0O_DATA_out1 1’d1 142 I2S0I_DATA_in2 0 no I2S0O_DATA_out2 1’d1 143 I2S0I_DATA_in3 0 no I2S0O_DATA_out3 1’d1 144 I2S0I_DATA_in4 0 no I2S0O_DATA_out4 1’d1 145 I2S0I_DATA_in5 0 no I2S0O_DATA_out5 1’d1 146 I2S0I_DATA_in6 0 no I2S0O_DATA_out6 1’d1 147 I2S0I_DATA_in7 0 no I2S0O_DATA_out7 1’d1 148 I2S0I_DATA_in8 0 no I2S0O_DATA_out8 1’d1 149 I2S0I_DATA_in9 0 no I2S0O_DATA_out9 1’d1 150 I2S0I_DATA_in10 0 no I2S0O_DATA_out10 1’d1 151 I2S0I_DATA_in11 0 no I2S0O_DATA_out11 1’d1 152 I2S0I_DATA_in12 0 no I2S0O_DATA_out12 1’d1 153 I2S0I_DATA_in13 0 no I2S0O_DATA_out13 1’d1 154 I2S0I_DATA_in14 0 no I2S0O_DATA_out14 1’d1 155 I2S0I_DATA_in15 0 no I2S0O_DATA_out15 1’d1 156 — — — I2S0O_DATA_out16 1’d1 157 — — — I2S0O_DATA_out17 1’d1 158 — — — I2S0O_DATA_out18 1’d1 159 — — — I2S0O_DATA_out19 1’d1 160 — — — I2S0O_DATA_out20 1’d1 161 — — — I2S0O_DATA_out21 1’d1 162 — — — I2S0O_DATA_out22 1’d1 163 — — — I2S0O_DATA_out23 1’d1 164 I2S1I_BCK_in 0 no I2S1I_BCK_out 1’d1 165 I2S1I_WS_in 0 no I2S1I_WS_out 1’d1 166 I2S1I_DATA_in0 0 no I2S1O_DATA_out0 1’d1 167 I2S1I_DATA_in1 0 no I2S1O_DATA_out1 1’d1 168 I2S1I_DATA_in2 0 no I2S1O_DATA_out2 1’d1 169 I2S1I_DATA_in3 0 no I2S1O_DATA_out3 1’d1 170 I2S1I_DATA_in4 0 no I2S1O_DATA_out4 1’d1 171 I2S1I_DATA_in5 0 no I2S1O_DATA_out5 1’d1 Espressif Systems 66 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A Signal No. Input Signals Default Value If Unassigned* Same Input Sig- nal from IO_MUX Core Output Signals Output Enable of Output Signals 172 I2S1I_DATA_in6 0 no I2S1O_DATA_out6 1’d1 173 I2S1I_DATA_in7 0 no I2S1O_DATA_out7 1’d1 174 I2S1I_DATA_in8 0 no I2S1O_DATA_out8 1’d1 175 I2S1I_DATA_in9 0 no I2S1O_DATA_out9 1’d1 176 I2S1I_DATA_in10 0 no I2S1O_DATA_out10 1’d1 177 I2S1I_DATA_in11 0 no I2S1O_DATA_out11 1’d1 178 I2S1I_DATA_in12 0 no I2S1O_DATA_out12 1’d1 179 I2S1I_DATA_in13 0 no I2S1O_DATA_out13 1’d1 180 I2S1I_DATA_in14 0 no I2S1O_DATA_out14 1’d1 181 I2S1I_DATA_in15 0 no I2S1O_DATA_out15 1’d1 182 — — — I2S1O_DATA_out16 1’d1 183 — — — I2S1O_DATA_out17 1’d1 184 — — — I2S1O_DATA_out18 1’d1 185 — — — I2S1O_DATA_out19 1’d1 186 — — — I2S1O_DATA_out20 1’d1 187 — — — I2S1O_DATA_out21 1’d1 188 — — — I2S1O_DATA_out22 1’d1 189 — — — I2S1O_DATA_out23 1’d1 190 I2S0I_H_SYNC 0 no pwm3_out1h 1’d1 191 I2S0I_V_SYNC 0 no pwm3_out1l 1’d1 192 I2S0I_H_ENABLE 0 no pwm3_out2h 1’d1 193 I2S1I_H_SYNC 0 no pwm3_out2l 1’d1 194 I2S1I_V_SYNC 0 no pwm3_out3h 1’d1 195 I2S1I_H_ENABLE 0 no pwm3_out3l 1’d1 196 — — — pwm3_out4h 1’d1 197 — — — pwm3_out4l 1’d1 198 U2RXD_in 0 yes U2TXD_out 1’d1 199 U2CTS_in 0 yes U2RTS_out 1’d1 200 emac_mdc_i 0 no emac_mdc_o emac_mdc_oe 201 emac_mdi_i 0 no emac_mdo_o emac_mdo_o_e 202 emac_crs_i 0 no emac_crs_o emac_crs_oe 203 emac_col_i 0 no emac_col_o emac_col_oe 204 pcmfsync_in 0 no bt_audio0_irq 1’d1 205 pcmclk_in 0 no bt_audio1_irq 1’d1 206 pcmdin 0 no bt_audio2_irq 1’d1 207 — — — ble_audio0_irq 1’d1 208 — — — ble_audio1_irq 1’d1 209 — — — ble_audio2_irq 1’d1 210 — — — pcmfsync_out pcmfsync_en 211 — — — pcmclk_out pcmclk_en Espressif Systems 67 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A Signal No. Input Signals Default Value If Unassigned* Same Input Sig- nal from IO_MUX Core Output Signals Output Enable of Output Signals 212 — — — pcmdout pcmdout_en 213 — — — ble_audio_sync0_p 1’d1 214 — — — ble_audio_sync1_p 1’d1 215 — — — ble_audio_sync2_p 1’d1 224 — — — sig_in_func224 1’d1 225 — — — sig_in_func225 1’d1 226 — — — sig_in_func226 1’d1 227 — — — sig_in_func227 1’d1 228 — — — sig_in_func228 1’d1 A.3. Ethernet_MAC Table 6-3. Ethernet_MAC Pin Name Function6 MII (int_osc) MII (ext_osc) RMII (int_osc) RMII (ext_osc) GPIO0 EMAC_TX_CLK TX_CLK (I) TX_CLK (I) CLK_OUT(O) EXT_OSC_CLK(I) GPIO5 EMAC_RX_CLK RX_CLK (I) RX_CLK (I) — — GPIO21 EMAC_TX_EN TX_EN(O) TX_EN(O) TX_EN(O) TX_EN(O) GPIO19 EMAC_TXD0 TXD[0](O) TXD[0](O) TXD[0](O) TXD[0](O) GPIO22 EMAC_TXD1 TXD[1](O) TXD[1](O) TXD[1](O) TXD[1](O) MTMS EMAC_TXD2 TXD[2](O) TXD[2](O) — — MTDI EMAC_TXD3 TXD[3](O) TXD[3](O) — — MTCK EMAC_RX_ER RX_ER(I) RX_ER(I) — — GPIO27 EMAC_RX_DV RX_DV(I) RX_DV(I) CRS_DV(I) CRS_DV(I) GPIO25 EMAC_RXD0 RXD[0](I) RXD[0](I) RXD[0](I) RXD[0](I) GPIO26 EMAC_RXD1 RXD[1](I) RXD[1](I) RXD[1](I) RXD[1](I) U0TXD EMAC_RXD2 RXD[2](I) RXD[2](I) — — MTDO EMAC_RXD3 RXD[3](I) RXD[3](I) — — GPIO16 EMAC_CLK_OUT CLK_OUT(O) — CLK_OUT(O) — GPIO17 EMAC_CLK_OUT_180 CLK_OUT_180(O) — CLK_OUT_180(O) — GPIO4 EMAC_TX_ER TX_ERR(O)* TX_ERR(O)* — — In GPIO Matrix* — MDC(O) MDC(O) MDC(O) MDC(O) In GPIO Matrix* — MDIO(IO) MDIO(IO) MDIO(IO) MDIO(IO) In GPIO Matrix* — CRS(I) CRS(I) — — In GPIO Matrix* — COL(I) COL(I) — — *Notes: 1. The GPIO Matrix can be any GPIO. 2. The TX_ERR (O) is optional. A.4. IO_MUX For the list of IO_MUX pins, please see the next page. Espressif Systems 68 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Appendix A IO_MUX Pin No. Power Supply Pin Analog Pin Digital Pin Power Domain Analog Function0 Analog Function1 Analog Function2 RTC Function0 RTC Function1 Function0 Type Function1 Type Function2 Type Function3 Type Function4 Type Function5 Type Drive Strength (2’d2: 20 mA) At Reset After Reset 1 VDDA VDDA supply in 2 LNA_IN VDD3P3 3 VDD3P3 VDD3P3 supply in 4 VDD3P3 VDD3P3 supply in 5 SENSOR_VP VDD3P3_RTC ADC1_CH0 RTC_GPIO0 GPIO36 I GPIO36 I oe=0, ie=0 oe=0, ie=0 6 SENSOR_CAPP VDD3P3_RTC ADC1_CH1 RTC_GPIO1 GPIO37 I GPIO37 I oe=0, ie=0 oe=0, ie=0 7 SENSOR_CAPN VDD3P3_RTC ADC1_CH2 RTC_GPIO2 GPIO38 I GPIO38 I oe=0, ie=0 oe=0, ie=0 8 SENSOR_VN VDD3P3_RTC ADC1_CH3 RTC_GPIO3 GPIO39 I GPIO39 I oe=0, ie=0 oe=0, ie=0 9 CHIP_PU VDD3P3_RTC 10 VDET_1 VDD3P3_RTC ADC1_CH6 RTC_GPIO4 GPIO34 I GPIO34 I oe=0, ie=0 oe=0, ie=0 11 VDET_2 VDD3P3_RTC ADC1_CH7 RTC_GPIO5 GPIO35 I GPIO35 I oe=0, ie=0 oe=0, ie=0 12 32K_XP VDD3P3_RTC XTAL_32K_P ADC1_CH4 TOUCH9 RTC_GPIO9 GPIO32 I/O/T GPIO32 I/O/T 2'd2 oe=0, ie=0 oe=0, ie=0 13 32K_XN VDD3P3_RTC XTAL_32K_N ADC1_CH5 TOUCH8 RTC_GPIO8 GPIO33 I/O/T GPIO33 I/O/T 2'd2 oe=0, ie=0 oe=0, ie=0 14 GPIO25 VDD3P3_RTC DAC_1 ADC2_CH8 RTC_GPIO6 GPIO25 I/O/T GPIO25 I/O/T EMAC_RXD0 I 2'd2 oe=0, ie=0 oe=0, ie=0 15 GPIO26 VDD3P3_RTC DAC_2 ADC2_CH9 RTC_GPIO7 GPIO26 I/O/T GPIO26 I/O/T EMAC_RXD1 I 2'd2 oe=0, ie=0 oe=0, ie=0 16 GPIO27 VDD3P3_RTC ADC2_CH7 TOUCH7 RTC_GPIO17 GPIO27 I/O/T GPIO27 I/O/T EMAC_RX_DV I 2'd2 oe=0, ie=0 oe=0, ie=0 17 MTMS VDD3P3_RTC ADC2_CH6 TOUCH6 RTC_GPIO16 MTMS I0 HSPICLK I/O/T GPIO14 I/O/T HS2_CLK O SD_CLK I0 EMAC_TXD2 O 2'd2 oe=0, ie=0 oe=0, ie=1, wpu 18 MTDI VDD3P3_RTC ADC2_CH5 TOUCH5 RTC_GPIO15 MTDI I1 HSPIQ I/O/T GPIO12 I/O/T HS2_DATA2 I1/O/T SD_DATA2 I1/O/T EMAC_TXD3 O 2'd2 oe=0, ie=1, wpd oe=0, ie=1, wpd 19 VDD3P3_RTC VDD3P3_RTC supply in 20 MTCK VDD3P3_RTC ADC2_CH4 TOUCH4 RTC_GPIO14 MTCK I1 HSPID I/O/T GPIO13 I/O/T HS2_DATA3 I1/O/T SD_DATA3 I1/O/T EMAC_RX_ER I 2'd2 oe=0, ie=0 oe=0, ie=1, wpd 21 MTDO VDD3P3_RTC ADC2_CH3 TOUCH3 RTC_GPIO13 I2C_SDA MTDO O/T HSPICS0 I/O/T GPIO15 I/O/T HS2_CMD I1/O/T SD_CMD I1/O/T EMAC_RXD3 I 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 22 GPIO2 VDD3P3_RTC ADC2_CH2 TOUCH2 RTC_GPIO12 I2C_SCL GPIO2 I/O/T HSPIWP I/O/T GPIO2 I/O/T HS2_DATA0 I1/O/T SD_DATA0 I1/O/T 2'd2 oe=0, ie=1, wpd oe=0, ie=1, wpd 23 GPIO0 VDD3P3_RTC ADC2_CH1 TOUCH1 RTC_GPIO11 I2C_SDA GPIO0 I/O/T CLK_OUT1 O GPIO0 I/O/T EMAC_TX_CLK I 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 24 GPIO4 VDD3P3_RTC ADC2_CH0 TOUCH0 RTC_GPIO10 I2C_SCL GPIO4 I/O/T HSPIHD I/O/T GPIO4 I/O/T HS2_DATA1 I1/O/T SD_DATA1 I1/O/T EMAC_TX_ER O 2'd2 oe=0, ie=1, wpd oe=0, ie=1, wpd 25 GPIO16 VDD_SDIO GPIO16 I/O/T GPIO16 I/O/T HS1_DATA4 I1/O/T U2RXD I1 EMAC_CLK_OUT O 2'd2 oe=0, ie=0 oe=0, ie=1 26 VDD_SDIO VDD_SDIO supply out/in 27 GPIO17 VDD_SDIO GPIO17 I/O/T GPIO17 I/O/T HS1_DATA5 I1/O/T U2TXD O EMAC_CLK_OUT_180 O 2'd2 oe=0, ie=0 oe=0, ie=1 28 SD_DATA_2 VDD_SDIO SD_DATA2 I1/O/T SPIHD I/O/T GPIO9 I/O/T HS1_DATA2 I1/O/T U1RXD I1 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 29 SD_DATA_3 VDD_SDIO SD_DATA3 I0/O/T SPIWP I/O/T GPIO10 I/O/T HS1_DATA3 I1/O/T U1TXD O 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 30 SD_CMD VDD_SDIO SD_CMD I1/O/T SPICS0 I/O/T GPIO11 I/O/T HS1_CMD I1/O/T U1RTS O 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 31 SD_CLK VDD_SDIO SD_CLK I0 SPICLK I/O/T GPIO6 I/O/T HS1_CLK O U1CTS I1 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 32 SD_DATA_0 VDD_SDIO SD_DATA0 I1/O/T SPIQ I/O/T GPIO7 I/O/T HS1_DATA0 I1/O/T U2RTS O 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 33 SD_DATA_1 VDD_SDIO SD_DATA1 I1/O/T SPID I/O/T GPIO8 I/O/T HS1_DATA1 I1/O/T U2CTS I1 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 34 GPIO5 VDD3P3_CPU GPIO5 I/O/T VSPICS0 I/O/T GPIO5 I/O/T HS1_DATA6 I1/O/T EMAC_RX_CLK I 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 35 GPIO18 VDD3P3_CPU GPIO18 I/O/T VSPICLK I/O/T GPIO18 I/O/T HS1_DATA7 I1/O/T 2'd2 oe=0, ie=0 oe=0, ie=1 36 GPIO23 VDD3P3_CPU GPIO23 I/O/T VSPID I/O/T GPIO23 I/O/T HS1_STROBE I0 2'd2 oe=0, ie=0 oe=0, ie=1 37 VDD3P3_CPU VDD3P3_CPU supply in 38 GPIO19 VDD3P3_CPU GPIO19 I/O/T VSPIQ I/O/T GPIO19 I/O/T U0CTS I1 EMAC_TXD0 O 2'd2 oe=0, ie=0 oe=0, ie=1 39 GPIO22 VDD3P3_CPU GPIO22 I/O/T VSPIWP I/O/T GPIO22 I/O/T U0RTS O EMAC_TXD1 O 2'd2 oe=0, ie=0 oe=0, ie=1 40 U0RXD VDD3P3_CPU U0RXD I1 CLK_OUT2 O GPIO3 I/O/T 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 41 U0TXD VDD3P3_CPU U0TXD O CLK_OUT3 O GPIO1 I/O/T EMAC_RXD2 I 2'd2 oe=0, ie=1, wpu oe=0, ie=1, wpu 42 GPIO21 VDD3P3_CPU GPIO21 I/O/T VSPIHD I/O/T GPIO21 I/O/T EMAC_TX_EN O 2'd2 oe=0, ie=0 oe=0, ie=1 43 VDDA VDDA supply in 44 XTAL_N VDDA 45 XTAL_P VDDA 46 VDDA VDDA supply in 47 CAP2 VDDA 48 CAP1 VDDA Total Number 8 14 26 Notes: • wpu: weak pull-up; • wpd: weak pull-down; • ie: input enable; • oe: output enable; • Please see Table: Notes on ESP32 Pin Lists for more information.（请参考表：管脚清单说明。） Espressif Systems 69 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Revision History Date Version Release notes 2025.11 v5.2 • ESP32-D0WDR2-V3 is end of life and upgraded to ESP32-D0WDRH2-V3 • Table 1-1 Comparison: Updated ”Ordering Code” to ”Part Number” 2025.10 v5.1 • Section 4.8.3 Universal Asynchronous Receiver Transmitter (UART): Added description ”Programmable baud rates up to 5 MBaud” • Section 3 Boot Configurations: Fixed the typo about Internal LDO (VDD_SDIO) Voltage Control • Fixed other typos 2025.08 v5.0 • Table 2-3 Power Pins: Added power pin 1 VDDA • Updated Figure 3-1 Visualization of Timing Parameters for the Strapping Pins • Table 5-3 DC Characteristics (3.3 V, 25 °C): Added V IH _nRST 2025.04 v4.9 • Section CPU and Memory: Improved CoreMark scores • Section 3.1 Chip Boot Mode Control: Modified the description from ”valid only for ESP32 ECO V3” to ”valid only for ESP32 chip revisions v3.0 and higher” • Section 4.8.2 Serial Peripheral Interface (SPI): Added information about SPI • Table 2-2 Analog Pins: Fixed typos about pin numbers 2025.01 v4.8 • Section 3 Boot Configurations: Fixed the typo about JTAG signal source control • Section 2.2 Pin Overview: Added a note about JTAG interface signals • Table 2-5 Pin Mapping Between Chip and Flash/PSRAM: Modified a note about VDD_SDIO 2024.09 v4.7 • Table 5-2 Recommended Power Supply Characteristics: Deleted a note about VDD3P3_RTC limitation • Section 4.1.1 CPU: Fixed the link to Cadence Xtensa ISA Summary • Section 4.8.7 Pulse Counter Controller (PCNT): Fixed the typo in the Feature List 2024.08 v4.6 Improved the formatting, structure, and wording in the following sections: • Section 2 Pins • Section 3 Boot Configurations (used to be named as ”Strapping Pins”) • Section 4 Functional Description 2024.02 v4.5 Section 2.5.3 Chip Power-up and Reset: Updated the link to the VDD_SDIO 1.8 V circuit design to ESP32 Hardware Design Guidelines Cont’d on next page Espressif Systems 70 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Cont’d from previous page Date Version Release notes 2023.12 v4.4 Table 1-1 Comparison: Added information about flash under the table 2023.07 v4.3 • Updated formatting throughout the document • Updated wording in some sections • Added a new section 2.3.1 Restrictions for GPIOs and RTC_GPIOs • Added a new section 4.1.5 Cache 2023.01 v4.2 • Removed contents about hall sensor according to PCN20221202 • Section 4.9.3 Touch Sensor: Added a note about limited applications of touch sensor 2022.12 v4.1 • Section 4.1.1 CPU: Added link to Xtensa ® Instruction Set Architecture (ISA) Summary • Table 1-1 Comparison: Updated the description about chip revision upgrade 2022.10 v4.0 • Section Product Overview: Updated the description • Table 2-6 Pin Mapping Between Chip and Flash/PSRAM: Added two notes below the table • Section 2.5.2 Power Scheme: Added a new item to “Notes on power supply” • Updated Figure 1-1 ESP32 Series Nomenclature • Table 1-1 Comparison: Added a new column “VDD_SDIO Voltage” • Section 4.8.12 TWAI ® Controller: Updated the bit rates • Added Not Recommended for New Designs (NRND) label to ESP32-S0WD 2022.03 v3.9 • Added a new chip variant ESP32-D0WDR2-V3 • Added Table 2-5 Pin Mapping Between Chip and Flash/PSRAM and Table 2-6 Pin Mapping Between Chip and Flash/PSRAM • Updated Figure 6-2 QFN48 (5x5 mm) Package • Updated Appendix IO_MUX • Updated Table 4-6 Peripheral Pin Configurations • Section 3.1 Chip Boot Mode Control: Added links to ESP32 Technical Reference Manual Cont’d on next page Espressif Systems 71 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Cont’d from previous page Date Version Release notes 2021.10 v3.8 • Upgraded ESP32-U4WDH variant from single-core to dual-core, see PCN-2021-021. The single-core version coexists with the new dual-core version around December 2, 2021. The physical product is subject to batch tracking. • Section CPU and Memory: Added CoreMark ® score • Section 4.8.12 TWAI ® Controller: Updated the description • Added Not Recommended for New Designs (NRND) label to the ESP32-D0WDQ6-V3 variant • Section 6 Packaging: Provided a link to Espressif Chip Package Information • Updated Section Bluetooth 2021.07 v3.7 • Removed ESP32-D2WD variant • Section 4.7.1 Bluetooth Radio and Baseband: Updated wording • Updated pin function numbers starting from Function0 • Added Not Recommended for New Designs (NRND) label to ESP32-D0WD and ESP32-D0WDQ6 variants 2021.03 V3.6 • Updated Figure Block Diagram • Updated Table 5-5 Reliability • Updated Figure 2-3 ESP32 Power Scheme • Updated Table 5-2 Recommended Power Supply Characteristics • Updated the notes below Table 2-4 Description of Timing Parameters for Power-up and Reset • Table 4-1, 4-6, Section 4.8.12 TWAI ® Controller: Added more information about TWAI ® 2021.01 V3.5 • Table 2-1 Pin Overview: Updated the description for CAP2 from 3 nF to 3.3 nF • Section Advanced Peripheral Interfaces: Added TWAI ® • Updated Figure Block Diagram • Appendix IO_MUX: Updated the reset values for MTCK, MTMS, GPIO27 2020.04 V3.4 • Added one chip variant: ESP32-U4WDH • Updated some figures in Table 4-2, 5-6, 5-7, 5-9, 5-11, 5-12 • Table 5-7 Receiver –Basic Data Rate: Added a note under the table 2020.01 V3.3 • Added two chip variants: ESP32-D0WD-V3 and ESP32-D0WDQ6-V3. • Added a note under Table 4-3 Analog-to-Digital Converter (ADC) Cont’d on next page Espressif Systems 72 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Cont’d from previous page Date Version Release notes 2019.10 V3.2 • Updated Figure 2-4 Visualization of Timing Parameters for Power-up and Reset 2019.07 V3.1 • Table 2-1 Pin Overview: Added pin-pin mapping between ESP32-D2WD and the in-package flash under the table • Updated Figure 1-1 ESP32 Series Nomenclature 2019.04 V3.0 • Section 3 Boot Configurations (used to be named as ”Strapping Pins”): Added information about the setup and hold times for the strapping pins 2019.02 V2.9 • Table 2-1 Pin Overview: Applied new formatting • Table 4-6 Peripheral Pin Configurations: Fixed typos with respect to the ADC1 channel mappings 2019.01 V2.8 • Changed the RF power control range in Table 5-7, 5-10, and 5-12 from –12 ~ +12 to –12 ~ +9 dBm; • Small text changes 2018.11 V2.7 • Updated Section Applications • Table IO_MUX: Updated pin statuses at reset and after reset 2018.10 V2.6 • Section 6 Packaging: Updated QFN package drawings 2018.08 V2.5 • Table 5-1 Absolute Maximum Ratings: Added ”Cumulative IO output current” • Table 5-3 DC Characteristics (3.3 V, 25 °C): Added more parameters • Appendix IO_MUX: Changed the power domain names to be consistent with the pin names 2018.07 V2.4 • Deleted information on Packet Traffic Arbitration (PTA); • Added Figure 2-4 Visualization of Timing Parameters for Power-up and Reset • Table 4-2 Power Management Unit (PMU): Added the current consumption figures for dual-core SoCs • Updated Section 4.9.1 Analog-to-Digital Converter (ADC) Cont’d on next page Espressif Systems 73 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Cont’d from previous page Date Version Release notes 2018.06 V2.3 • Table 4-2 Power Management Unit (PMU): Added the current consumption figures at CPU frequency of 160 MHz 2018.05 V2.2 • Table 2-1 Pin Overview: Changed the voltage range of VDD3P3_RTC from 1.8-3.6 V to 2.3-3.6 V • Updated Section 2.5.2 Power Scheme • Updated Section 4.1.3 External Flash and RAM • Updated Table 4-2 Power Management Unit (PMU) • Removed content about temperature sensor; Changes to electrical characteristics: • Updated Table 5-1 Absolute Maximum Ratings • Added Table 5-2 Recommended Power Supply Characteristics • Added Table 5-3 DC Characteristics (3.3 V, 25 °C) • Added Table 5-5 Reliability • Table 5-7 Receiver –Basic Data Rate: Updated the values of ”Gain control step” and ”Adjacent channel transmit power” • Table 5-10 Transmitter –Enhanced Data Rate: Updated the values of ”Gain control step”, ”π/4 DQPSK modulation accuracy”, ”8 DPSK modulation accuracy”, and ”In-band spurious emissions” • Table 5-12 Transmitter: Updated the values of ”Gain control step” and ”Adjacent channel transmit power” 2018.01 V2.1 • Deleted software-specific features; • Deleted information on LNA pre-amplifier; • Specified the CPU speed and flash speed of ESP32-D2WD; • Section 2.5.2 Power Scheme: Added notes 2017.12 V2.0 • Section 6 Packaging: Added a note on the sequence of pin number 2017.10 V1.9 • Table 2-1 Pin Overview: Updated the description of pin CHIP_PU • Section 2.5.2 Power Scheme: Added a note • Section 3 Boot Configurations (used to be named as ”Strapping Pins”): Updated the description of the chip’s system reset • Section 4.6.4 Wi-Fi Radio and Baseband: Added a description of antenna diversity and selection • Table 4-2 Power Management Unit (PMU): Deleted ”Association sleep pattern”, added notes to Active sleep and Modem-sleep Cont’d on next page Espressif Systems 74 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Cont’d from previous page Date Version Release notes 2017.08 V1.8 • Added Table 4-6 Peripheral Pin Configurations • Figure Block Diagram: Corrected a typo 2017.08 V1.7 • Section Bluetooth: Changed the transmitting power to +12 dBm; the sensitivity of NZIF receiver to –97 dBm • Table 2-1 Pin Overview: Added a note • section 4.1.1 CPU: Added 160 MHz clock frequency • Section 4.6.4 Wi-Fi Radio and Baseband: Changed the transmitting power from 21 dBm to 20.5 dBm • Section 4.7.1 Bluetooth Radio and Baseband: Changed the dynamic control range of class-1, class-2 and class-3 transmit output powers to ”up to 24 dBm”; changed the dynamic range of NZIF receiver sensitivity to ”over 97 dB” • Table 4-2 Power Management Unit (PMU): Added two notes • Updated Section 4.8.1 General Purpose Input / Output Interface (GPIO) • Updated Section 4.8.11 SDIO/SPI Slave Controller • Updated Table 5-1 Absolute Maximum Ratings • Table 5.4 RF Current Consumption in Active Mode: Changed the duty cycle on which the transmitters’measurements are based to 50%. • Table 5-6 Wi-Fi Radio: Added a note on “Output impedance” • Table 5-7, 5-9, 5-11: Updated parameter ”Sensitivity” • Table 5-7, 5-10, 5-12: Updated parameters ”RF transmit power” and ”RF power control range”; added parameter ”Gain control step” • Deleted Chapters: ”Touch Sensor” and ”Code Examples”; • Added a link to certification download. 2017.06 V1.6 • Section Complete Integration Solution: Changed the number of external components to 20 • Section 4.8.1 General Purpose Input / Output Interface (GPIO): Changed the number of GPIO pins to 34 2017.06 V1.5 • Section CPU and Memory: Changed the power supply range • Section 2.5.2 Power Scheme: Updated the note • Updated Table 5-1 Absolute Maximum Ratings • Table Notes on ESP32 Pin Lists: Changed the drive strength values of the digital output pins in Note 8 • Added the option to subscribe for notifications of documentation changes Cont’d on next page Espressif Systems 75 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Revision History Cont’d from previous page Date Version Release notes 2017.05 V1.4 • Section Clocks and Timers: Added a note to the frequency of the external crystal oscillator • Section 3 Boot Configurations (used to be named as ”Strapping Pins”): Added a note • Updated Section 4.3 RTC and Low-power Management • Table 5-1 Absolute Maximum Ratings: Changed the maximum driving capability from 12 mA to 80 mA • Table 5-6 Wi-Fi Radio: Changed the input impedance value of 50Ω to output impedance value of 30+j10 Ω • Table Notes on ESP32 Pin Lists: Added a note to No.8 • Table IO_MUX: Deleted GPIO20 2017.04 V1.3 • Added Appendix Notes on ESP32 Pin Lists • Updated Table 5-6 Wi-Fi Radio • Updated Figure 2-2 ESP32 Pin Layout (QFN 5*5, Top View) 2017.03 V1.2 • Table 2-1 Pin Overview: Added a note • Section 4.1.2 Internal Memory: Updated the note 2017.02 V1.1 • Added Section 1 ESP32 Series Comparison • Updated Section MCU and Advanced Features • Updated Section Block Diagram • Updated Section 2 Pins • Updated Section CPU and Memory • Updated Section 4.2.3 Audio PLL Clock • Updated Section 5.1 Absolute Maximum Ratings • Updated Section 6 Packaging • Updated Section Related Documentation and Resources 2016.08 V1.0 First release. Espressif Systems 76 Submit Documentation Feedback ESP32 Series Datasheet v5.2 Disclaimer and Copyright Notice Information in this document, including URL references, is subject to change without notice. ALL THIRD PARTY’S INFORMATION IN THIS DOCUMENT IS PROVIDED AS IS WITH NO WARRANTIES TO ITS AUTHENTICITY AND ACCURACY. NO WARRANTY IS PROVIDED TO THIS DOCUMENT FOR ITS MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, NOR DOES ANY WARRANTY OTHERWISE ARISING OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE. All liability, including liability for infringement of any proprietary rights, relating to use of information in this document is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are granted herein. The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is a registered trademark of Bluetooth SIG. All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged. Copyright © 2025 Espressif Systems (Shanghai) Co., Ltd. All rights reserved. www.espressif.com