1 Module Overview 1.1 Features 1.2 Series Comparison 1.3 Applications 2 Block Diagram 3 Pin Definitions 3.1 Pin Layout 3.2 Pin Description 4 Boot Configurations 4.1 Chip Boot Mode Control 4.2 Internal LDO (VDD_SDIO) Voltage Control 4.3 U0TXD Printing Control 4.4 Timing Control of SDIO Slave 4.5 JTAG Signal Source Control 4.6 Chip Power-up and Reset 5 Peripherals 5.1 Peripheral Overview 5.2 Digital Peripherals 5.2.1 General Purpose Input / Output Interface (GPIO) 5.2.2 Serial Peripheral Interface (SPI) 5.2.3 Universal Asynchronous Receiver Transmitter (UART) 5.2.4 I2C Interface 5.2.5 I2S Interface 5.2.6 Remote Control Peripheral 5.2.7 Pulse Counter Controller (PCNT) 5.2.8 LED PWM Controller 5.2.9 Motor Control PWM 5.2.10 SD/SDIO/MMC Host Controller 5.2.11 SDIO/SPI Slave Controller 5.2.12 TWAI Controller 5.2.13 Ethernet MAC Interface 5.3 Analog Peripherals 5.3.1 Analog-to-Digital Converter (ADC) 5.3.2 Digital-to-Analog Converter (DAC) 5.3.3 Touch Sensor 6 Electrical Characteristics 6.1 Absolute Maximum Ratings 6.2 Recommended Operating Conditions 6.3 DC Characteristics (3.3 V, 25 °C) 6.4 Current Consumption in Active Mode 6.5 Memory Specifications 7 RF Characteristics 7.1 Wi-Fi Radio 7.1.1 Wi-Fi RF Transmitter (TX) Characteristics 7.1.2 Wi-Fi RF Receiver (RX) Characteristics 7.2 Bluetooth Radio 7.2.1 Receiver – Basic Data Rate 7.2.2 Transmitter – Basic Data Rate 7.2.3 Receiver – Enhanced Data Rate 7.2.4 Transmitter – Enhanced Data Rate 7.3 Bluetooth LE Radio 7.3.1 Receiver 7.3.2 Transmitter 8 Module Schematics 9 Peripheral Schematics 10 Physical Dimensions 10.1 Module Dimensions 10.2 Dimensions of External Antenna Connector 11 PCB Layout Recommendations 11.1 PCB Land Pattern 11.2 Module Placement for PCB Design 12 Product Handling 12.1 Storage Conditions 12.2 Electrostatic Discharge (ESD) 12.3 Reflow Profile 12.4 Ultrasonic Vibration Datasheet Versioning Related Documentation and Resources Revision History ESP32-WROVER-E & ESP32-WROVER-IE Datasheet Version 2.3 www.espressif.com 1 Module Overview 1 Module Overview Note: Check the link or the QR code to make sure that you use the latest version of this document: https://espressif.com/documentation/esp32-wrover-e_esp32-wrover-ie_datasheet_en.pdf 1.1 Features CPU and On-Chip Memory • ESP32-D0WD-V3 or ESP32-D0WDR2-V3 embedded, Xtensa dual-core 32-bit LX6 microprocessor, up to 240 MHz • 448 KB ROM • 520 KB SRAM • 16 KB SRAM in RTC Wi-Fi • 802.11b/g/n • Bit rate: 802.11n up to 150 Mbps • A-MPDU and A-MSDU aggregation • 0.4 µs guard interval support • Center frequency range of operating channel: 2412 ~ 2484 MHz Bluetooth ® • Bluetooth V4.2 BR/EDR and Bluetooth LE specification • Class-1, class-2 and class-3 transmitter • AFH • CVSD and SBC Peripherals • Up to 24 GPIOs – 5 strapping GPIOs • SD card, UART, SPI, SDIO, I2C, LED PWM, Motor PWM, I2S, IR, pulse counter, GPIO, capacitive touch sensor, ADC, DAC, TWAI ® (compatible with ISO 11898-1, i.e. CAN Specification 2.0) Integrated Components on Module • 40 MHz crystal oscillator • 4/8/16 MB SPI flash • ESP32-D0WDR2-V3 also provides 2 MB PSRAM Antenna Options • ESP32-WROVER-E: On-board PCB antenna • ESP32-WROVER-IE: external antenna via a connector Operating Conditions • Operating voltage/Power supply: 3.0 ~ 3.6 V • Operating ambient temperature: –40 ~ 85 °C Certification • Bluetooth certification: BQB • RF certification: See certificates for ESP32-WROVER-E and ESP32-WROVER-IE • Green certification: REACH/RoHS Test • HTOL/HTSL/uHAST/TCT/ESD Espressif Systems 1 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 1 Module Overview 1.2 Series Comparison ESP32-WROVER-E and ESP32-WROVER-IE are two powerful, generic Wi-Fi + Bluetooth + Bluetooth LE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding. ESP32-WROVER-E comes with a PCB antenna, and ESP32-WROVER-IE with a connector for an external antenna. The information in this datasheet is applicable to both modules. The Series Comparison for the two modules is as follows: Table 1: ESP32-WROVER-E Series Comparison 1 Ambient Temp. 2 Size 3 VDD_SDIO Part Number Flash 5 PSRAM (°C) (mm) Voltage ESP32-WROVER-E-N4R8 4 MB (Quad SPI) 8 MB (Quad SPI) –40 ~ 85 18.0 × 31.4 × 3.3 3.3 V ESP32-WROVER-E-N8R8 8 MB (Quad SPI) 8 MB (Quad SPI) –40 ~ 85 ESP32-WROVER-E-N16R8 16 MB (Quad SPI) 8 MB (Quad SPI) –40 ~ 85 ESP32-WROVER-E-N4R2 (EOL) 4 MB (Quad SPI) 2 MB (Quad SPI) 4 –40 ~ 85 ESP32-WROVER-E-N8R2 (EOL) 8 MB (Quad SPI) 2 MB (Quad SPI) 4 –40 ~ 85 ESP32-WROVER-E-N16R2 (EOL) 16 MB (Quad SPI) 2 MB (Quad SPI) 4 –40 ~ 85 1 This table shares the same notes presented in the table 2 below. Table 2: ESP32-WROVER-IE Series Comparison Ambient Temp. 2 Size 3 VDD_SDIO Part Number Flash 5 PSRAM (°C) (mm) Voltage ESP32-WROVER-IE-N4R8 4 MB (Quad SPI) 8 MB (Quad SPI) –40 ~ 85 18.0 × 31.4 × 3.3 3.3 V ESP32-WROVER-IE-N8R8 8 MB (Quad SPI) 8 MB (Quad SPI) –40 ~ 85 ESP32-WROVER-IE-N16R8 16 MB (Quad SPI) 8 MB (Quad SPI) –40 ~ 85 ESP32-WROVER-IE-N4R2 (EOL) 4 MB (Quad SPI) 2 MB (Quad SPI) 4 –40 ~ 85 ESP32-WROVER-IE-N8R2 (EOL) 8 MB (Quad SPI) 2 MB (Quad SPI) 4 –40 ~ 85 ESP32-WROVER-IE-N16R2 (EOL) 16 MB (Quad SPI) 2 MB (Quad SPI) 4 –40 ~ 85 2 Ambient temperature specifies the recommended temperature range of the environment immediately outside the Espressif module. 3 For details, refer to Section 10.1 Module Dimensions. 4 This module uses PSRAM integrated in the chip’s package. 5 For specifications, refer to Section 6.5 Memory Specifications. At the core of the module is the ESP32-D0WD-V3 chip or ESP32-D0WDR2-V3 chip (EOL)*. ESP32-D0WD-V3 chip and ESP32-D0WDR2-V3 chip* are designed to be scalable and adaptive. There are two CPU cores that can be individually controlled, and the CPU clock frequency is adjustable from 80 MHz to 240 MHz. The chip also has a low-power coprocessor that can be used instead of the CPU to save power while performing tasks that do not require much computing power, such as monitoring of peripherals. Espressif Systems 2 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 1 Module Overview Note: • For details on the part numbers of the ESP32 family of chips, please refer to the document ESP32 Datasheet. • For chip revision identification, ESP-IDF release that supports a specific chip revision, and other information on chip revisions, please refer to ESP32 Series SoC Errata > Section Chip Revision Identification. 1.3 Applications • Smart Home • Industrial Automation • Health Care • Consumer Electronics • Smart Agriculture • POS Machines • Service Robot • Audio Devices • Generic Low-power IoT Sensor Hubs • Generic Low-power IoT Data Loggers • Cameras for Video Streaming • Speech Recognition • Image Recognition • SDIO Wi-Fi + Bluetooth Networking Card Espressif Systems 3 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Contents Contents 1 Module Overview 1 1.1 Features 1 1.2 Series Comparison 2 1.3 Applications 3 2 Block Diagram 8 3 Pin Definitions 10 3.1 Pin Layout 10 3.2 Pin Description 11 4 Boot Configurations 13 4.1 Chip Boot Mode Control 14 4.2 Internal LDO (VDD_SDIO) Voltage Control 15 4.3 U0TXD Printing Control 16 4.4 Timing Control of SDIO Slave 16 4.5 JTAG Signal Source Control 16 4.6 Chip Power-up and Reset 16 5 Peripherals 18 5.1 Peripheral Overview 18 5.2 Digital Peripherals 18 5.2.1 General Purpose Input / Output Interface (GPIO) 18 5.2.2 Serial Peripheral Interface (SPI) 18 5.2.3 Universal Asynchronous Receiver Transmitter (UART) 19 5.2.4 I2C Interface 19 5.2.5 I2S Interface 20 5.2.6 Remote Control Peripheral 20 5.2.7 Pulse Counter Controller (PCNT) 21 5.2.8 LED PWM Controller 21 5.2.9 Motor Control PWM 22 5.2.10 SD/SDIO/MMC Host Controller 23 5.2.11 SDIO/SPI Slave Controller 23 5.2.12 TWAI ® Controller 24 5.2.13 Ethernet MAC Interface 25 5.3 Analog Peripherals 25 5.3.1 Analog-to-Digital Converter (ADC) 25 5.3.2 Digital-to-Analog Converter (DAC) 26 5.3.3 Touch Sensor 27 6 Electrical Characteristics 28 6.1 Absolute Maximum Ratings 28 6.2 Recommended Operating Conditions 28 Espressif Systems 4 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Contents 6.3 DC Characteristics (3.3 V, 25 °C) 28 6.4 Current Consumption in Active Mode 29 6.5 Memory Specifications 29 7 RF Characteristics 31 7.1 Wi-Fi Radio 31 7.1.1 Wi-Fi RF Transmitter (TX) Characteristics 31 7.1.2 Wi-Fi RF Receiver (RX) Characteristics 32 7.2 Bluetooth Radio 33 7.2.1 Receiver – Basic Data Rate 33 7.2.2 Transmitter – Basic Data Rate 34 7.2.3 Receiver – Enhanced Data Rate 34 7.2.4 Transmitter – Enhanced Data Rate 35 7.3 Bluetooth LE Radio 36 7.3.1 Receiver 36 7.3.2 Transmitter 36 8 Module Schematics 37 9 Peripheral Schematics 39 10 Physical Dimensions 40 10.1 Module Dimensions 40 10.2 Dimensions of External Antenna Connector 42 11 PCB Layout Recommendations 44 11.1 PCB Land Pattern 44 11.2 Module Placement for PCB Design 45 12 Product Handling 46 12.1 Storage Conditions 46 12.2 Electrostatic Discharge (ESD) 46 12.3 Reflow Profile 46 12.4 Ultrasonic Vibration 47 Datasheet Versioning 48 Related Documentation and Resources 49 Revision History 50 Espressif Systems 5 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 List of Tables List of Tables 1 ESP32-WROVER-E Series Comparison 1 2 2 ESP32-WROVER-IE Series Comparison 2 3 Pin Definitions 11 4 Default Configuration of Strapping Pins 13 5 Description of Timing Parameters for the Strapping Pins 14 6 Chip Boot Mode Control 14 7 U0TXD Printing Control 16 8 Timing Control of SDIO Slave 16 9 Description of Timing Parameters for Power-up and Reset 17 10 ADC Characteristics 26 11 ADC Calibration Results 26 12 Capacitive-Sensing GPIOs Available on ESP32 27 13 Absolute Maximum Ratings 28 14 Recommended Operating Conditions 28 15 DC Characteristics (3.3 V, 25 °C) 28 16 Current Consumption for Wi-Fi (2.4 GHz) in Active Mode 29 17 Flash Specifications 30 18 PSRAM Specifications 30 19 Wi-Fi RF Characteristics 31 20 TX Power with Spectral Mask and EVM Meeting 802.11 Standards 31 21 TX EVM Test 1 31 22 RX Sensitivity 32 23 Maximum RX Level 33 24 RX Adjacent Channel Rejection 33 25 Bluetooth LE RF Characteristics 33 26 Receiver Characteristics – Basic Data Rate 33 27 Transmitter Characteristics – Basic Data Rate 34 28 Receiver Characteristics – Enhanced Data Rate 34 29 Transmitter Characteristics – Enhanced Data Rate 35 30 Receiver Characteristics – Bluetooth LE 36 31 Transmitter Characteristics – Bluetooth LE 36 Espressif Systems 6 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 List of Figures List of Figures 1 ESP32-WROVER-E Block Diagram (with ESP32-D0WD-V3 embedded) 8 2 ESP32-WROVER-E Block Diagram (with ESP32-D0WDR2-V3 embedded) 8 3 ESP32-WROVER-IE Block Diagram (with ESP32-D0WD-V3 embedded) 9 4 ESP32-WROVER-IE Block Diagram (with ESP32-D0WDR2-V3 embedded) 9 5 Pin Layout (Top View) 10 6 Visualization of Timing Parameters for the Strapping Pins 14 7 Chip Boot Flow 15 8 Visualization of Timing Parameters for Power-up and Reset 16 9 Schematics of ESP32-WROVER-E 37 10 Schematics of ESP32-WROVER-IE 38 11 Peripheral Schematics 39 12 ESP32-WROVER-E Physical Dimensions 40 13 ESP32-WROVER-IE Physical Dimensions 41 14 Dimensions of External Antenna Connector 42 15 Recommended PCB Land Pattern 44 16 Reflow Profile 46 Espressif Systems 7 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 2 Block Diagram 2 Block Diagram Note: For the pin mapping between the chip and the in-package flash/PSRAM, please refer to ESP32 Series Datasheet > Table Pin Mapping Between Chip and In-package Flash/PSRAM. RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WDR2-V3 40 MHz Crystal 3V3 EN GPIOs ESP32-WROVER-E ESP32-D0WDR2-V3 RF Matching Antenna ESP32-D0WD-V3 RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WD-V3 40 MHz Crystal 3V3 EN GPIOs FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 ESP32-WROVER-E RF Matching Antenna QSPI PSRAM QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH QSPI PSRAM QSPI PSRAM FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 QSPI PSRAM QSPI FLASH Figure 1: ESP32-WROVER-E Block Diagram (with ESP32-D0WD-V3 embedded) RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WDR2-V3 40 MHz Crystal 3V3 EN GPIOs ESP32-WROVER-E ESP32-D0WDR2-V3 RF Matching Antenna ESP32-D0WD-V3 RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WD-V3 40 MHz Crystal 3V3 EN GPIOs FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 ESP32-WROVER-E RF Matching Antenna QSPI PSRAM QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH QSPI PSRAM QSPI PSRAM FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 QSPI PSRAM QSPI FLASH Figure 2: ESP32-WROVER-E Block Diagram (with ESP32-D0WDR2-V3 embedded) Espressif Systems 8 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 2 Block Diagram RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WDR2-V3 40 MHz Crystal 3V3 EN GPIOs ESP32-WROVER-E ESP32-D0WDR2-V3 RF Matching Antenna ESP32-D0WD-V3 RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WD-V3 40 MHz Crystal 3V3 EN GPIOs FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 ESP32-WROVER-E RF Matching Antenna QSPI PSRAM QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH QSPI PSRAM QSPI PSRAM FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 QSPI PSRAM QSPI FLASH Figure 3: ESP32-WROVER-IE Block Diagram (with ESP32-D0WD-V3 embedded) RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WDR2-V3 40 MHz Crystal 3V3 EN GPIOs ESP32-WROVER-E ESP32-D0WDR2-V3 RF Matching Antenna ESP32-D0WD-V3 RF Matching 40 MHz Crystal 3V3 EN GPIOs Antenna ESP32-WROVER-IE ESP32-D0WD-V3 40 MHz Crystal 3V3 EN GPIOs FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 ESP32-WROVER-E RF Matching Antenna QSPI PSRAM QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH SPICS SPICLK SPIDI SPIDO SPIHD SPIWP VDD_SDIO QSPI FLASH QSPI PSRAM QSPI PSRAM FLASH_CLK SPIHD SPIDO SPIDI SPICS0 SPIWP VDD_SDIO PSRAM_CLK SPICS1 VDD_SDIO SIO0 SIO1 SIO2 SIO3 QSPI PSRAM QSPI FLASH Figure 4: ESP32-WROVER-IE Block Diagram (with ESP32-D0WDR2-V3 embedded) Espressif Systems 9 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 3 Pin Definitions 3 Pin Definitions 3.1 Pin Layout The pin diagram below shows the approximate location of pins on the module. For the actual diagram drawn to scale, please refer to Figure 10.1 Module Dimensions. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 GND 3V3 EN SENSOR_VP SENSOR_VN IO34 IO35 IO32 IO33 IO25 IO26 IO27 IO14 IO12 15 16 17 18 19 GND IO13 NC NC NC 38 37 36 35 34 33 32 31 30 29 28 27 26 25 GND IO23 IO22 TXD0 RXD0 IO21 NC IO19 IO18 IO5 NC NC IO4 IO0 Pin 39 GND Keepout Zone GND GND GND GND GND GNDGNDGND 24 23 22 21 20 IO2 IO15 NC NC NC A Figure 5: Pin Layout (Top View) Espressif Systems 10 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 3 Pin Definitions Note A: • The zone marked with dotted lines is the antenna keepout zone. The pin layout of ESP32-WROVER-IE is the same as that of ESP32-WROVER-E, except that ESP32-WROVER-IE has no keepout zone. • To learn more about the keepout zone for module’s antenna on the base board, please refer to ESP32 Hardware Design Guidelines > Section Positioning a Module on a Base Board. 3.2 Pin Description The module has 38 pins. See pin definitions in Table 3 Pin Description. For peripheral pin configurations, please refer to Section 5.2 Digital Peripherals. Table 3: Pin Definitions Name No. Type 1 Function GND 1 P Ground 3V3 2 P Power supply EN 3 I Module-enable signal. Active high. SENSOR_VP 4 I GPIO36, ADC1_CH0, RTC_GPIO0 SENSOR_VN 5 I GPIO39, ADC1_CH3, RTC_GPIO3 IO34 6 I GPIO34, ADC1_CH6, RTC_GPIO4 IO35 7 I GPIO35, ADC1_CH7, RTC_GPIO5 IO32 8 I/O GPIO32, XTAL_32K_P (32.768 kHz crystal oscillator input), ADC1_CH4, TOUCH9, RTC_GPIO9 IO33 9 I/O GPIO33, XTAL_32K_N (32.768 kHz crystal oscillator output), ADC1_CH5, TOUCH8, RTC_GPIO8 IO25 10 I/O GPIO25, DAC_1, ADC2_CH8, RTC_GPIO6, EMAC_RXD0 IO26 11 I/O GPIO26, DAC_2, ADC2_CH9, RTC_GPIO7, EMAC_RXD1 IO27 12 I/O GPIO27, ADC2_CH7, TOUCH7, RTC_GPIO17, EMAC_RX_DV IO14 13 I/O GPIO14, ADC2_CH6, TOUCH6, RTC_GPIO16, MTMS, HSPICLK, HS2_CLK, SD_CLK, EMAC_TXD2 IO12 14 I/O GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3 GND 15 P Ground IO13 16 I/O GPIO13, ADC2_CH4, TOUCH4, RTC_GPIO14, MTCK, HSPID, HS2_DATA3, SD_DATA3, EMAC_RX_ER NC 17 - See note 2 NC 18 - See note 2 NC 19 - See note 2 NC 20 - See note 2 NC 21 - See note 2 NC 22 - See note 2 IO15 23 I/O GPIO15, ADC2_CH3, TOUCH3, MTDO, HSPICS0, RTC_GPIO13, HS2_CMD, SD_CMD, EMAC_RXD3 Cont’d on next page Espressif Systems 11 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 3 Pin Definitions Table 3 – cont’d from previous page Name No. Type 1 Function IO2 24 I/O GPIO2, ADC2_CH2, TOUCH2, RTC_GPIO12, HSPIWP, HS2_DATA0, SD_DATA0 IO0 25 I/O GPIO0, ADC2_CH1, TOUCH1, RTC_GPIO11, CLK_OUT1, EMAC_TX_CLK IO4 26 I/O GPIO4, ADC2_CH0, TOUCH0, RTC_GPIO10, HSPIHD, HS2_DATA1, SD_DATA1, EMAC_TX_ER NC 27 - - NC 28 - - IO5 29 I/O GPIO5, VSPICS0, HS1_DATA6, EMAC_RX_CLK IO18 30 I/O GPIO18, VSPICLK, HS1_DATA7 IO19 31 I/O GPIO19, VSPIQ, U0CTS, EMAC_TXD0 NC 32 - - IO21 33 I/O GPIO21, VSPIHD, EMAC_TX_EN RXD0 34 I/O GPIO3, U0RXD, CLK_OUT2 TXD0 35 I/O GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2 IO22 36 I/O GPIO22, VSPIWP, U0RTS, EMAC_TXD1 IO23 37 I/O GPIO23, VSPID, HS1_STROBE GND 38 P Ground 1 P: power supply; I: input; O: output. 2 Pins GPIO6 to GPIO11 on the ESP32-D0WD-V3/ESP32-D0WDR2-V3 chip are connected to the SPI flash integrated on the module and are not led out. Espressif Systems 12 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 4 Boot Configurations 4 Boot Configurations Note: The content below is excerpted from ESP32 Series Datasheet > Section Boot Configurations. For the strapping pin map- ping between the chip and modules, please refer to Chapter 8 Module Schematics. The chip allows for configuring the following boot parameters through strapping pins and eFuse bits at power-up or a hardware reset, without microcontroller interaction. • Chip boot mode – Strapping pin: GPIO0 and GPIO2 • Internal LDO (VDD_SDIO) Voltage – Strapping pin: MTDI – eFuse bit: EFUSE_SDIO_FORCE and EFUSE_SDIO_TIEH • U0TXD printing – Strapping pin: MTDO • Timing of SDIO Slave – Strapping pin: MTDO and GPIO5 • JTAG signal source – eFuse bit: EFUSE_DISABLE_JTAG The default values of all the above eFuse bits are 0, which means that they are not burnt. Given that eFuse is one-time programmable, once an eFuse bit is programmed to 1, it can never be reverted to 0. For how to program eFuse bits, please refer to ESP32 Technical Reference Manual > Chapter eFuse Controller. The default values of the strapping pins, namely the logic levels, are determined by pins’ internal weak pull-up/pull-down resistors at reset if the pins are not connected to any circuit, or connected to an external high-impedance circuit. Table 4: Default Configuration of Strapping Pins Strapping Pin Default Configuration Bit Value GPIO0 Pull-up 1 GPIO2 Pull-down 0 MTDI Pull-down 0 MTDO Pull-up 1 GPIO5 Pull-up 1 To change the bit values, the strapping pins should be connected to external pull-down/pull-up resistances. If the ESP32 is used as a device by a host MCU, the strapping pin voltage levels can also be controlled by the host MCU. All strapping pins have latches. At system reset, the latches sample the bit values of their respective strapping pins and store them until the chip is powered down or shut down. The states of latches cannot be changed in any other way. It makes the strapping pin values available during the entire chip operation, and the pins are freed up to be used as regular IO pins after reset. Espressif Systems 13 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 4 Boot Configurations The timing of signals connected to the strapping pins should adhere to the setup time and hold time specifications in Table 5 and Figure 6. Table 5: Description of Timing Parameters for the Strapping Pins Parameter Description Min (ms) t SU Setup time is the time reserved for the power rails to stabilize before the CHIP_PU pin is pulled high to activate the chip. 0 t H Hold time is the time reserved for the chip to read the strapping pin values after CHIP_PU is already high and before these pins start operating as regular IO pins. 1 Strapping pin V IH_nRST V IH t SU t H CHIP_PU Figure 6: Visualization of Timing Parameters for the Strapping Pins 4.1 Chip Boot Mode Control GPIO0 and GPIO2 control the boot mode after the reset is released. See Table 6 Chip Boot Mode Control. Table 6: Chip Boot Mode Control Boot Mode GPIO0 GPIO2 SPI Boot Mode 1 Any value Joint Download Boot Mode 2 0 0 1 Bold marks the default value and configuration. 2 Joint Download Boot mode supports the following download methods: • SDIO Download Boot • UART Download Boot In Joint Download Boot mode, the detailed boot flow of the chip is put below 7. Espressif Systems 14 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 4 Boot Configurations Figure 7: Chip Boot Flow uart_download_dis controls boot mode behaviors: It permanently disables Download Boot mode when uart_download_dis is set to 1 (valid only for ESP32 chip revisions v3.0 and higher). 4.2 Internal LDO (VDD_SDIO) Voltage Control MTDI is used to select the VDD_SDIO power supply voltage at reset: • MTDI = 0 (by default), VDD_SDIO pin is powered directly from VDD3P3_RTC. Typically this voltage is 3.3 V. For more information, see ESP32 Series Datasheet > Section Power Scheme. • MTDI = 1, VDD_SDIO pin is powered from internal 1.8 V LDO. This functionality can be overridden by setting EFUSE_SDIO_FORCE to 1, in which case the EFUSE_SDIO_TIEH determines the VDD_SDIO voltage: • EFUSE_SDIO_TIEH = 0, VDD_SDIO connects to 1.8 V LDO. • EFUSE_SPI_TIEH = 1, VDD_SDIO connects to VDD3P3_RTC. Espressif Systems 15 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 4 Boot Configurations 4.3 U0TXD Printing Control During booting, the strapping pin MTDO can be used to control the U0TXD Printing, as Table 7 shows. Table 7: U0TXD Printing Control U0TXD Printing Control MTDO Enabled 1 1 Disabled 0 1 Bold marks the default value and configuration. 4.4 Timing Control of SDIO Slave The strapping pin MTDO and GPIO5 can be used to control the timing of SDIO slave, see Table 8 Timing Control of SDIO Slave. Table 8: Timing Control of SDIO Slave Edge behavior MTDO GPIO5 Falling edge sampling, falling edge output 0 0 Falling edge sampling, rising edge output 0 1 Rising edge sampling, falling edge output 1 0 Rising edge sampling, rising edge output 1 1 1 Bold marks the default value and configuration. 4.5 JTAG Signal Source Control If EFUSE_DISABLE_JTAG is set to 1, the source of JTAG signals can be disabled. 4.6 Chip Power-up and Reset Once the power is supplied to the chip, its power rails need a short time to stabilize. After that, CHIP_PU – the pin used for power-up and reset – is pulled high to activate the chip. For information on CHIP_PU as well as power-up and reset timing, see Figure 8 and Table 9. V IL_nRST t ST BL t RST VDD3P3_RTC Min VDD CHIP_PU Figure 8: Visualization of Timing Parameters for Power-up and Reset Espressif Systems 16 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 4 Boot Configurations Table 9: Description of Timing Parameters for Power-up and Reset Parameter Description Min (µs) t ST BL Time reserved for the 3.3 V rails to stabilize before the CHIP_PU pin is pulled high to activate the chip 50 t RST Time reserved for CHIP_PU to stay below V IL_nRST to reset the chip (see Table 15) 50 For details, please refer to ESP32 Series Datasheet > Section Chip Power-up and Reset. Espressif Systems 17 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals 5 Peripherals 5.1 Peripheral Overview ESP32-D0WD-V3 chip and ESP32-D0WDR2-V3 chip integrate a rich set of peripherals including SPI, I2S, UART, I2C, pulse count controller, TWAI ® , ADC, DAC, touch sensor, etc. To learn more about on-chip components, please refer to ESP32 Series Datasheet > Section Functional Description. Note: • The content below is sourced from ESP32 Series Datasheet > Section Functional Description. Some information may not be applicable to ESP32-WROVER-E and ESP32-WROVER-IE as not all the IO signals are exposed on the module. • To learn more about peripheral signals, please refer to ESP32 Technical Reference Manual > Section Peripheral Signal List. 5.2 Digital Peripherals 5.2.1 General Purpose Input / Output Interface (GPIO) ESP32 has 34 GPIO pins which can be assigned various functions by programming the appropriate registers. There are several kinds of GPIOs: digital-only, analog-enabled, capacitive-touch-enabled, etc. Analog-enabled GPIOs and Capacitive-touch-enabled GPIOs can be configured as digital GPIOs. Most of the digital GPIOs can be configured as internal pull-up or pull-down, or set to high impedance. When configured as an input, the input value can be read through the register. The input can also be set to edge-trigger or level-trigger to generate CPU interrupts. Most of the digital IO pins are bi-directional, non-inverting and tristate, including input and output buffers with tristate control. These pins can be multiplexed with other functions, such as the SDIO, UART, SPI, etc. (More details can be found in ESP32 Series Datasheet > Appendix, Table IO_MUX. ) For low-power operations, the GPIOs can be set to hold their states. For details, see ESP32 Series Datasheet > Section Peripheral Pin Configurations, ESP32 Series Datasheet > Appendix A – ESP32 Pin Lists and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.2 Serial Peripheral Interface (SPI) ESP32 integrates four SPI controllers which can be used to communicate with external devices that use the SPI protocol. Controller SPI0 is used as a buffer for accessing external memory. Controller SPI1 can be used as a master. Controllers SPI2 and SPI3 can be configured as either a master or a slave. SPI1, SPI2, and SPI3 use signal buses prefixed with SPI, HSPI, and VSPI, respectively. Features of General Purpose SPI (GP-SPI) • Programmable data transfer length, in multiples of 1 byte • Four-line full-duplex/half-duplex communication and three-line half-duplex communication support Espressif Systems 18 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals • Master mode and slave mode • Programmable CPOL and CPHA • Programmable clock For details, see ESP32 Technical Reference Manual > Chapter SPI Controller. Pin Assignment For SPI, the pins are multiplexed with GPIO6 ~ GPIO11 via the IO MUX. For HSPI, the pins are multiplexed with GPIO2, GPIO4, GPIO12 ~ GPIO15 via the IO MUX. For VSPI, the pins are multiplexed with GPIO5, GPIO18 ~ GPIO19, GPIO21 ~ GPIO23 via the IO MUX. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.3 Universal Asynchronous Receiver Transmitter (UART) The UART in the ESP32 chip facilitates the transmission and reception of asynchronous serial data between the chip and external UART devices. It consists of two UARTs in the main system, and one low-power LP UART. Feature List • Programmable baud rates up to 5 MBaud • RAM shared by TX FIFOs and RX FIFOs • Supports input baud rate self-check • Support for various lengths of data bits and stop bits • Parity bit support • Asynchronous communication (RS232 and RS485) and IrDA support • Supports DMA to communicate data in high speed • Supports UART wake-up • Supports both software and hardware flow control For details, see ESP32 Technical Reference Manual > Chapter UART Controller. Pin Assignment The pins for UART can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.4 I2C Interface ESP32 has two I2C bus interfaces which can serve as I2C master or slave, depending on the user’s configuration. Espressif Systems 19 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals Feature List • Two I2C controllers: one in the main system and one in the low-power system • Standard mode (100 Kbit/s) • Fast mode (400 Kbit/s) • Up to 5 MHz, yet constrained by SDA pull-up strength • Support for 7-bit and 10-bit addressing, as well as dual address mode • Supports continuous data transmission with disabled Serial Clock Line (SCL) • Supports programmable digital noise filter Users can program command registers to control I2C interfaces, so that they have more flexibility. For details, see ESP32 Technical Reference Manual > Chapter I2C Controller. Pin Assignment For regular I2C, the pins used can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.5 I2S Interface The I2S Controller in the ESP32 chip provides a flexible communication interface for streaming digital data in multimedia applications, particularly digital audio applications. Feature List • Master mode and slave mode • Full-duplex and half-duplex communications • A variety of audio standards supported • Configurable high-precision output clock • Supports PDM signal input and output • Configurable data transmit and receive modes For details, see ESP32 Technical Reference Manual > Chapter I2S Controller. Pin Assignment The pins for the I2S Controller can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.6 Remote Control Peripheral The Remote Control Peripheral (RMT) controls the transmission and reception of infrared remote control signals. Espressif Systems 20 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals Feature List • Eight channels for sending and receiving infrared remote control signals • Independent transmission and reception capabilities for each channel • Clock divider counter, state machine, and receiver for each RX channel • Supports various infrared protocols For details, see ESP32 Technical Reference Manual > Chapter Remote Control Peripheral. Pin Assignment The pins for the Remote Control Peripheral can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.7 Pulse Counter Controller (PCNT) The pulse counter controller (PCNT) is designed to count input pulses by tracking rising and falling edges of the input pulse signal. Feature List • Eight independent pulse counter units • Each pulse counter unit has a 16-bit signed counter register and two channels • Counter modes: increment, decrement, or disable • Glitch filtering for input pulse signals and control signals • Selection between counting on rising or falling edges of the input pulse signal For details, see ESP32 Technical Reference Manual > Chapter Pulse Count Controller. Pin Assignment The pins for the Pulse Count Controller can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.8 LED PWM Controller The LED PWM Controller (LEDC) is designed to generate PWM signals for LED control. Feature List • Sixteen independent PWM generators • Maximum PWM duty cycle resolution of 20 bits • Eight independent timers with 20-bit counters, configurable fractional clock dividers and counter overflow values Espressif Systems 21 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals • Adjustable phase of PWM signal output • PWM duty cycle dithering • Automatic duty cycle fading For details, see ESP32 Technical Reference Manual > Chapter LED PWM Controller. Pin Assignment The pins for the LED PWM Controller can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.9 Motor Control PWM The Pulse Width Modulation (PWM) controller can be used for driving digital motors and smart lights. The controller consists of PWM timers, the PWM operator and a dedicated capture sub-module. Each timer provides timing in synchronous or independent form, and each PWM operator generates a waveform for one PWM channel. The dedicated capture sub-module can accurately capture events with external timing. Feature List • Three PWM timers for precise timing and frequency control – Every PWM timer has a dedicated 8-bit clock prescaler – The 16-bit counter in the PWM timer can work in count-up mode, count-down mode, or count-up-down mode – A hardware sync can trigger a reload on the PWM timer with a phase register. It will also trigger the prescaler’ restart, so that the timer’s clock can also be synced, with selectable hardware synchronization source • Three PWM operators for generating waveform pairs – Six PWM outputs to operate in several topologies – Configurable dead time on rising and falling edges; each set up independently – Modulating of PWM output by high-frequency carrier signals, useful when gate drivers are insulated with a transformer • Fault Detection module – Programmable fault handling in both cycle-by-cycle mode and one-shot mode – A fault condition can force the PWM output to either high or low logic levels • Capture module for hardware-based signal processing – Speed measurement of rotating machinery – Measurement of elapsed time between position sensor pulses – Period and duty cycle measurement of pulse train signals Espressif Systems 22 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals – Decoding current or voltage amplitude derived from duty-cycle-encoded signals of current/voltage sensors – Three individual capture channels, each of which with a 32-bit time-stamp register – Selection of edge polarity and prescaling of input capture signals – The capture timer can sync with a PWM timer or external signals For details, see ESP32 Technical Reference Manual > Chapter Motor Control PWM. Pin Assignment The pins for the Motor Control PWM can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.10 SD/SDIO/MMC Host Controller An SD/SDIO/MMC host controller is available on ESP32. Feature List • Supports two external cards • Supports SD Memory Card standard: version 3.0 and version 3.01) • Supports SDIO Version 3.0 • Supports Consumer Electronics Advanced Transport Architecture (CE-ATA Version 1.1) • Supports Multimedia Cards (MMC version 4.41, eMMC version 4.5 and version 4.51) The controller allows up to 80 MHz clock output in three different data-bus modes: 1-bit, 4-bit, and 8-bit modes. It supports two SD/SDIO/MMC4.41 cards in a 4-bit data-bus mode. It also supports one SD card operating at 1.8 V. For details, see ESP32 Technical Reference Manual > Chapter SD/MMC Host Controller. Pin Assignment The pins for SD/SDIO/MMC Host Controller are multiplexed with GPIO2, GPIO4, GPIO6 ~ GPIO15 via IO MUX. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.11 SDIO/SPI Slave Controller ESP32 integrates an SD device interface that conforms to the industry-standard SDIO Card Specification Version 2.0, and allows a host controller to access the SoC, using the SDIO bus interface and protocol. ESP32 acts as the slave on the SDIO bus. The host can access the SDIO-interface registers directly and can access shared memory via a DMA engine, thus maximizing performance without engaging the processor cores. Espressif Systems 23 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals Feature List The SDIO/SPI slave controller supports the following features: • SPI, 1-bit SDIO, and 4-bit SDIO transfer modes over the full clock range from 0 to 50 MHz • Configurable sampling and driving clock edge • Special registers for direct access by host • Interrupts to host for initiating data transfer • Automatic loading of SDIO bus data and automatic discarding of padding data • Block size of up to 512 bytes • Interrupt vectors between the host and the slave, allowing both to interrupt each other • Supports DMA for data transfer For details, see ESP32 Technical Reference Manual > Chapter SDIO Slave Controller. Pin Assignment The pins for SDIO/SPI Slave Controller are multiplexed with GPIO2, GPIO4, GPIO6 ~ GPIO15 via IO MUX. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.12 TWAI ® Controller The Two-wire Automotive Interface (TWAI ® ) is a multi-master, multi-cast communication protocol designed for automotive applications. The TWAI controller facilitates the communication based on this protocol. Feature List • Compatible with ISO 11898-1 protocol (CAN Specification 2.0) • Standard frame format (11-bit ID) and extended frame format (29-bit ID) • Bit rates: – From 25 Kbit/s to 1 Mbit/s in chip revision v0.0/v1.0/v1.1 – From 12.5 Kbit/s to 1 Mbit/s in chip revision v3.0/v3.1 • Multiple modes of operation: Normal, Listen Only, and Self-Test • 64-byte receive FIFO • Special transmissions: single-shot transmissions and self reception • Acceptance filter (single and dual filter modes) • Error detection and handling: error counters, configurable error interrupt threshold, error code capture, arbitration lost capture For details, see ESP32 Technical Reference Manual > Chapter Two-wire Automotive Interface (TWAI). Espressif Systems 24 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals Pin Assignment The pins for the Two-wire Automotive Interface can be chosen from any GPIOs via the GPIO Matrix. For more information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.2.13 Ethernet MAC Interface An IEEE-802.3-2008-compliant Media Access Controller (MAC) is provided for Ethernet LAN communications. ESP32 requires an external physical interface device (PHY) to connect to the physical LAN bus (twisted-pair, fiber, etc.). The PHY is connected to ESP32 through 17 signals of MII or nine signals of RMII. Feature List • 10 Mbps and 100 Mbps rates • Dedicated DMA controller allowing high-speed transfer between the dedicated SRAM and Ethernet MAC • Tagged MAC frame (VLAN support) • Half-duplex (CSMA/CD) and full-duplex operation • MAC control sublayer (control frames) • 32-bit CRC generation and removal • Several address-filtering modes for physical and multicast address (multicast and group addresses) • 32-bit status code for each transmitted or received frame • Internal FIFOs to buffer transmit and receive frames. The transmit FIFO and the receive FIFO are both 512 words (32-bit) • Hardware PTP (Precision Time Protocol) in accordance with IEEE 1588 2008 (PTP V2) • 25 MHz/50 MHz clock output For details, see ESP32 Technical Reference Manual > Chapter Ethernet Media Access Controller (MAC). Pin Assignment For information about the pin assignment of Ethernet MAC Interface, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.3 Analog Peripherals 5.3.1 Analog-to-Digital Converter (ADC) ESP32 integrates two 12-bit SAR ADCs and supports measurements on 18 channels (analog-enabled pins). The ULP coprocessor in ESP32 is also designed to measure voltage, while operating in the sleep mode, which enables low-power consumption. The CPU can be woken up by a threshold setting and/or via other triggers. Table 10 describes the ADC characteristics. Espressif Systems 25 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals Table 10: ADC Characteristics Parameter Description Min Max Unit DNL (Differential nonlinearity) RTC controller; ADC connected to an –7 7 LSB external 100 nF capacitor; DC signal input; INL (Integral nonlinearity) ambient temperature at 25 °C; –12 12 LSB Wi-Fi&Bluetooth off Sampling rate RTC controller — 200 ksps DIG controller — 2 Msps Notes: • When atten = 3 and the measurement result is above 3000 (voltage at approx. 2450 mV), the ADC accuracy will be worse than described in the table above. • To get better DNL results, users can take multiple sampling tests with a filter, or calculate the average value. • The input voltage range of GPIO pins within VDD3P3_RTC domain should strictly follow the DC characteristics provided in Table 15. Otherwise, measurement errors may be introduced, and chip performance may be affected. By default, there are ±6% differences in measured results between chips. ESP-IDF provides couple of calibration methods for ADC1. Results after calibration using eFuse Vref value are shown in Table 11. For higher accuracy, users may apply other calibration methods provided in ESP-IDF, or implement their own. Table 11: ADC Calibration Results Parameter Description Min Max Unit Total error Atten = 0, effective measurement range of 100 ∼ 950 mV –23 23 mV Atten = 1, effective measurement range of 100 ∼ 1250 mV –30 30 mV Atten = 2, effective measurement range of 150 ∼ 1750 mV –40 40 mV Atten = 3, effective measurement range of 150 ∼ 2450 mV –60 60 mV For details, see ESP32 Technical Reference Manual > Chapter On-Chip Sensors and Analog Signal Processing. Pin Assignment With appropriate settings, the ADCs can be configured to measure voltage on 18 pins maximum. For detailed information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.3.2 Digital-to-Analog Converter (DAC) Two 8-bit DAC channels can be used to convert two digital signals into two analog voltage signal outputs. The design structure is composed of integrated resistor strings and a buffer. This dual DAC supports power supply as input voltage reference. The two DAC channels can also support independent conversions. For details, see ESP32 Technical Reference Manual > Chapter On-Chip Sensors and Analog Signal Processing. Espressif Systems 26 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 5 Peripherals Pin Assignment The DAC can be configured by GPIO 25 and GPIO 26. For detailed information about the pin assignment, see ESP32 Series Datasheet > Section Peripheral Pin Configurations and ESP32 Technical Reference Manual > Chapter IO_MUX and GPIO Matrix. 5.3.3 Touch Sensor ESP32 has 10 capacitive-sensing GPIOs, which detect variations induced by touching or approaching the GPIOs with a finger or other objects. The low-noise nature of the design and the high sensitivity of the circuit allow relatively small pads to be used. Arrays of pads can also be used, so that a larger area or more points can be detected. Pin Assignment The 10 capacitive-sensing GPIOs are listed in Table 12. Table 12: Capacitive-Sensing GPIOs Available on ESP32 Capacitive-Sensing Signal Name Pin Name T0 GPIO4 T1 GPIO0 T2 GPIO2 T3 MTDO T4 MTCK T5 MTDI T6 MTMS T7 GPIO27 T8 32K_XN T9 32K_XP For details, see ESP32 Technical Reference Manual > Chapter On-Chip Sensors and Analog Signal Processing. Note: ESP32 Touch Sensor has not passed the Conducted Susceptibility (CS) test for now, and thus has limited application scenarios. Espressif Systems 27 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 6 Electrical Characteristics 6 Electrical Characteristics 6.1 Absolute Maximum Ratings Stresses above those listed in Table 13 Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Table 14 Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Table 13: Absolute Maximum Ratings Symbol Parameter Min Max Unit VDD33 Power supply voltage –0.3 3.6 V T store Storage temperature –40 105 °C 6.2 Recommended Operating Conditions Table 14: Recommended Operating Conditions Symbol Parameter Min Typ Max Unit VDD33 Power supply voltage 3.0 3.3 3.6 V I V DD Current delivered by external power supply 0.5 — — A T Operating temperature –40 — 85 °C 6.3 DC Characteristics (3.3 V, 25 °C) Table 15: DC Characteristics (3.3 V, 25 °C) Symbol Parameter Min Typ Max Unit C IN Pin capacitance - 2 - pF V IH High-level input voltage 0.75×VDD 1 - VDD 1 +0.3 V V IL Low-level input voltage –0.3 - 0.25×VDD 1 V I IH High-level input current - - 50 nA I IL Low-level input current - - 50 nA V OH High-level output voltage 0.8×VDD 1 - - V V OL Low-level output voltage - - 0.1×VDD 1 V Cont’d on next page Espressif Systems 28 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 6 Electrical Characteristics Table 15 – cont’d from previous page Symbol Parameter Min Typ Max Unit I OH High-level source current (VDD 1 = 3.3 V, V OH >= 2.64 V, output drive strength set to the maximum) VDD3P3_CPU power domain 1, 2 - 40 - mA VDD3P3_RTC power domain 1, 2 - 40 - mA VDD_SDIO power domain 1, 3 - 20 - mA I OL Low-level sink current (VDD 1 = 3.3 V, V OL = 0.495 V, output drive strength set to the maximum) - 28 - mA R P U Resistance of internal pull-up resistor - 45 - kΩ R P D Resistance of internal pull-down resistor - 45 - kΩ V IH_nRST Chip reset release voltage (CHIP_PU voltage is within the specified range) 0.75 × VDD 1 — VDD 1 + 0.3 V V IL_nRST Low-level input voltage of CHIP_PU to shut down the chip - - 0.6 V 1 Please see Appendix IO MUX of ESP32 Series Datasheet for IO’s power domain. VDD is the I/O voltage for a particular power domain of pins. 2 For VDD3P3_CPU and VDD3P3_RTC power domain, per-pin current sourced in the same domain is gradually reduced from around 40 mA to around 29 mA, V OH >=2.64 V, as the number of current-source pins increases. 3 Pins occupied by flash and/or PSRAM in the VDD_SDIO power domain were excluded from the test. 6.4 Current Consumption in Active Mode The current consumption measurements are taken with a 3.3 V supply at 25 °C ambient temperature. TX current consumption is rated at a 100% duty cycle. RX current consumption is rated when the peripherals are disabled and the CPU idle. Table 16: Current Consumption for Wi-Fi (2.4 GHz) in Active Mode Work Mode RF Condition Description Peak (mA) Active (RF working) TX 802.11b, 1 Mbps, DSSS @ 19.5 dBm 350 802.11g, 54 Mbps, OFDM @ 14.0 dBm 243 802.11n, HT20, MCS7 @ 13.0 dBm 233 802.11n, HT40, MCS7 @ 13.0 dBm 229 RX 802.11b/g/n, HT20 108 802.11n, HT40 113 6.5 Memory Specifications The data below is sourced from the memory vendor datasheet. These values are guaranteed through design and/or characterization but are not fully tested in production. Devices are shipped with the memory erased. Espressif Systems 29 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 6 Electrical Characteristics Table 17: Flash Specifications Parameter Description Min Typ Max Unit VCC Power supply voltage (1.8 V) 1.65 1.80 2.00 V Power supply voltage (3.3 V) 2.7 3.3 3.6 V F C Maximum clock frequency 80 — — MHz — Program/erase cycles 100,000 — — cycles T RET Data retention time 20 — — years T P P Page program time — 0.8 5 ms T SE Sector erase time (4 KB) — 70 500 ms T BE1 Block erase time (32 KB) — 0.2 2 s T BE2 Block erase time (64 KB) — 0.3 3 s T CE Chip erase time (16 Mb) — 7 20 s Chip erase time (32 Mb) — 20 60 s Chip erase time (64 Mb) — 25 100 s Chip erase time (128 Mb) — 60 200 s Chip erase time (256 Mb) — 70 300 s Table 18: PSRAM Specifications Parameter Description Min Typ Max Unit VCC Power supply voltage (1.8 V) 1.62 1.80 1.98 V Power supply voltage (3.3 V) 2.7 3.3 3.6 V F C Maximum clock frequency 80 — — MHz Espressif Systems 30 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 7 RF Characteristics 7 RF Characteristics This section contains tables with RF characteristics of the Espressif product. The RF data is measured at the antenna port, where RF cable is connected, including the front-end loss. The external antennas used for the tests on the modules with external antenna connectors have an impedance of 50 Ω.Devices should operate in the center frequency range allocated by regional regulatory authorities. The target center frequency range and the target transmit power are configurable by software. See ESP RF Test Tool and Test Guide for instructions. Unless otherwise stated, the RF tests are conducted with a 3.3 V (±5%) supply at 25 ºC ambient temperature. 7.1 Wi-Fi Radio Table 19: Wi-Fi RF Characteristics Name Description Center frequency range of operating channel 2412 ~ 2484 MHz Wi-Fi wireless standard IEEE 802.11b/g/n 7.1.1 Wi-Fi RF Transmitter (TX) Characteristics Table 20: TX Power with Spectral Mask and EVM Meeting 802.11 Standards Min Typ Max Rate (dBm) (dBm) (dBm) 802.11b, 1 Mbps — 19.5 — 802.11b, 11 Mbps — 19.5 — 802.11g, 6 Mbps — 18.0 — 802.11g, 54 Mbps — 14.0 — 802.11n, HT20, MCS0 — 18.0 — 802.11n, HT20, MCS7 — 13.0 — 802.11n, HT40, MCS0 — 18.0 — 802.11n, HT40, MCS7 — 13.0 — Table 21: TX EVM Test 1 Min Typ Limit Rate (dB) (dB) (dB) 802.11b, 1 Mbps, DSSS — –25.0 –10.0 802.11b, 11 Mbps, CCK — –25.0 –10.0 802.11g, 6 Mbps, OFDM — –24.0 –5.0 802.11g, 54 Mbps, OFDM — –28.0 –25.0 802.11n, HT20, MCS0 — –24.0 –5.0 Cont’d on next page Espressif Systems 31 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 7 RF Characteristics Table 21 – cont’d from previous page Min Typ Limit Rate (dB) (dB) (dB) 802.11n, HT20, MCS7 — –30.0 –27.0 802.11n, HT40, MCS0 — –24.0 –5.0 802.11n, HT40, MCS7 — –30.0 –27.0 1 EVM is measured at the corresponding typical TX power provided in Table 20 Wi-Fi RF Transmitter (TX) Characteristics above. 7.1.2 Wi-Fi RF Receiver (RX) Characteristics For RX tests, the PER (packet error rate) limit is 8% for 802.11b, and 10% for 802.11g/n. Table 22: RX Sensitivity Min Typ Max Rate (dBm) (dBm) (dBm) 802.11b, 1 Mbps, DSSS — –97.0 — 802.11b, 2 Mbps, DSSS — –94.0 — 802.11b, 5.5 Mbps, CCK — –91.0 — 802.11b, 11 Mbps, CCK — –88.0 — 802.11g, 6 Mbps, OFDM — –93.0 — 802.11g, 9 Mbps, OFDM — –91.0 — 802.11g, 12 Mbps, OFDM — –90.0 — 802.11g, 18 Mbps, OFDM — –87.0 — 802.11g, 24 Mbps, OFDM — –84.0 — 802.11g, 36 Mbps, OFDM — –81.0 — 802.11g, 48 Mbps, OFDM — –77.0 — 802.11g, 54 Mbps, OFDM — –75.0 — 802.11n, HT20, MCS0 — –91.0 — 802.11n, HT20, MCS1 — –88.0 — 802.11n, HT20, MCS2 — –86.0 — 802.11n, HT20, MCS3 — -83.0 — 802.11n, HT20, MCS4 — –80.0 — 802.11n, HT20, MCS5 — –75.0 — 802.11n, HT20, MCS6 — –73.0 — 802.11n, HT20, MCS7 — –72.0 — 802.11n, HT40, MCS0 — –88.0 — 802.11n, HT40, MCS1 — –85.0 — 802.11n, HT40, MCS2 — –83.0 — 802.11n, HT40, MCS3 — –80.0 — 802.11n, HT40, MCS4 — –76.0 — 802.11n, HT40, MCS5 — –72.0 — 802.11n, HT40, MCS6 — –70.0 — 802.11n, HT40, MCS7 — –69.0 — Espressif Systems 32 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 7 RF Characteristics Table 23: Maximum RX Level Min Typ Max Rate (dBm) (dBm) (dBm) 802.11b, 1 Mbps — 5 — 802.11b, 11 Mbps — 5 — 802.11g, 6 Mbps — 0 — 802.11g, 54 Mbps — –8 — 802.11n, HT20, MCS0 — 0 — 802.11n, HT20, MCS7 — –8 — 802.11n, HT40, MCS0 — 0 — 802.11n, HT40, MCS7 — –8 — Table 24: RX Adjacent Channel Rejection Min Typ Max Rate (dB) (dB) (dB) 802.11b, 1 Mbps, DSSS — 35 — 802.11b, 11 Mbps, CCK — 35 — 802.11g, 6 Mbps, OFDM — 27 — 802.11g, 54 Mbps, OFDM — 13 — 802.11n, HT20, MCS0 — 27 — 802.11n, HT20, MCS7 — 12 — 802.11n, HT40, MCS0 — 16 — 802.11n, HT40, MCS7 — 7 — 7.2 Bluetooth Radio Table 25: Bluetooth LE RF Characteristics Name Description Center frequency range of operating channel 2402 ~ 2480 MHz RF transmit power range –12.0 ~ 9.0 dBm 7.2.1 Receiver – Basic Data Rate Table 26: Receiver Characteristics – Basic Data Rate Parameter Conditions Min Typ Max Unit Sensitivity @0.1% BER — –90 –89 –88 dBm Maximum received signal @0.1% BER — 0 — — dBm Co-channel C/I — — +7 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — — –6 dB F = F0 – 1 MHz — — –6 dB Cont’d on next page Espressif Systems 33 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 7 RF Characteristics Table 26 – cont’d from previous page Parameter Conditions Min Typ Max Unit F = F0 + 2 MHz — — –25 dB F = F0 – 2 MHz — — –33 dB F = F0 + 3 MHz — — –25 dB F = F0 – 3 MHz — — –45 dB Out-of-band blocking performance 30 MHz ~ 2000 MHz –10 — — dBm 2000 MHz ~ 2400 MHz –27 — — dBm 2500 MHz ~ 3000 MHz –27 — — dBm 3000 MHz ~ 12.5 GHz –10 — — dBm Intermodulation — –36 — — dBm 7.2.2 Transmitter – Basic Data Rate Table 27: Transmitter Characteristics – Basic Data Rate Parameter Conditions Min Typ Max Unit RF transmit power 1 — — 0 — dBm Gain control step — — 3 — dB RF power control range — –12 — +9 dBm +20 dB bandwidth — — 0.9 — MHz Adjacent channel transmit power F = F0 ± 2 MHz — –55 — dBm F = F0 ± 3 MHz — –55 — dBm F = F0 ± > 3 MHz — –59 — dBm ∆ f1 avg — — — 155 kHz ∆ f2 max — 127 — — kHz ∆ f2 avg /∆ f1 avg — — 0.92 — — ICFT — — –7 — kHz Drift rate — — 0.7 — kHz/50 µs Drift (DH1) — — 6 — kHz Drift (DH5) — — 6 — kHz 1 There are a total of eight power levels from 0 to 7, and the transmit power ranges from –12 dBm to 9 dBm. When the power level rises by 1, the transmit power increases by 3 dB. Power level 4 is used by default and the corresponding transmit power is 0 dBm. 7.2.3 Receiver – Enhanced Data Rate Table 28: Receiver Characteristics – Enhanced Data Rate Parameter Conditions Min Typ Max Unit π/4 DQPSK Sensitivity @0.01% BER — –90 –89 –88 dBm Maximum received signal @0.01% BER — — 0 — dBm Co-channel C/I — — 11 — dB Cont’d on next page Espressif Systems 34 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 7 RF Characteristics Table 28 – cont’d from previous page Parameter Conditions Min Typ Max Unit Adjacent channel selectivity C/I F = F0 + 1 MHz — –7 — dB F = F0 – 1 MHz — –7 — dB F = F0 + 2 MHz — –25 — dB F = F0 – 2 MHz — –35 — dB F = F0 + 3 MHz — –25 — dB F = F0 – 3 MHz — –45 — dB 8DPSK Sensitivity @0.01% BER — –84 –83 –82 dBm Maximum received signal @0.01% BER — — –5 — dBm C/I c-channel — — 18 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — 2 — dB F = F0 – 1 MHz — 2 — dB F = F0 + 2 MHz — –25 — dB F = F0 – 2 MHz — –25 — dB F = F0 + 3 MHz — –25 — dB F = F0 – 3 MHz — –38 — dB 7.2.4 Transmitter – Enhanced Data Rate Table 29: Transmitter Characteristics – Enhanced Data Rate Parameter Conditions Min Typ Max Unit RF transmit power (see note under Table 27) — — 0 — dBm Gain control step — — 3 — dB RF power control range — –12 — +9 dBm π/4 DQPSK max w0 — — –0.72 — kHz π/4 DQPSK max wi — — –6 — kHz π/4 DQPSK max |wi + w0| — — –7.42 — kHz 8DPSK max w0 — — 0.7 — kHz 8DPSK max wi — — –9.6 — kHz 8DPSK max |wi + w0| — — –10 — kHz π/4 DQPSK modulation accuracy RMS DEVM — 4.28 — % 99% DEVM — 100 — % Peak DEVM — 13.3 — % 8 DPSK modulation accuracy RMS DEVM — 5.8 — % 99% DEVM — 100 — % Peak DEVM — 14 — % In-band spurious emissions F = F0 ± 1 MHz — –46 — dBm F = F0 ± 2 MHz — –44 — dBm F = F0 ± 3 MHz — –49 — dBm F = F0 +/– > 3 MHz — — –53 dBm EDR differential phase coding — — 100 — % Espressif Systems 35 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 7 RF Characteristics 7.3 Bluetooth LE Radio 7.3.1 Receiver Table 30: Receiver Characteristics – Bluetooth LE Parameter Conditions Min Typ Max Unit Sensitivity @30.8% PER — –94 –93 –92 dBm Maximum received signal @30.8% PER — 0 — — dBm Co-channel C/I — — +10 — dB Adjacent channel selectivity C/I F = F0 + 1 MHz — –5 — dB F = F0 – 1 MHz — –5 — dB F = F0 + 2 MHz — –25 — dB F = F0 – 2 MHz — –35 — dB F = F0 + 3 MHz — –25 — dB F = F0 – 3 MHz — –45 — dB Out-of-band blocking performance 30 MHz ~ 2000 MHz –10 — — dBm 2000 MHz ~ 2400 MHz –27 — — dBm 2500 MHz ~ 3000 MHz –27 — — dBm 3000 MHz ~ 12.5 GHz –10 — — dBm Intermodulation — –36 — — dBm 7.3.2 Transmitter Table 31: Transmitter Characteristics – Bluetooth LE Parameter Conditions Min Typ Max Unit RF transmit power (see note under Table 27) — — 0 — dBm Gain control step — — 3 — dB RF power control range — –12 — +9 dBm Adjacent channel transmit power F = F0 ± 2 MHz — –55 — dBm F = F0 ± 3 MHz — –57 — dBm F = F0 ± > 3 MHz — –59 — dBm ∆ f1 avg — — — 265 kHz ∆ f2 max — 210 — — kHz ∆ f2 avg /∆ f1 avg — — +0.92 — — ICFT — — –10 — kHz Drift rate — — 0.7 — kHz/50 µs Drift — — 2 — kHz Espressif Systems 36 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 8 Module Schematics 8 Module Schematics This is the reference design of the module. 5 5 4 4 3 3 2 2 1 1 D D C C B B A A Pin.1 GND Pin.2 3V3 Pin.3 EN Pin.4 SENSOR_VP Pin.5 SENSOR_VN Pin.6 IO34 Pin.7 IO35 Pin.8 IO32 Pin.9 IO33 Pin.10 IO25 Pin.11 IO26 Pin.12 IO27 Pin.13 IO14 Pin.23 IO15 Pin.37 IO23 Pin.36 IO22 Pin.28 NC Pin.32 NC Pin.27 NC Pin.25 IO0 Pin.35 U0TXD Pin.30 IO18 Pin.26 IO4 Pin.34 U0RXD Pin.29 IO5 Pin.33 IO21 Pin.31 IO19 Pin.14 IO12 Pin.20 NC Pin.21 NC Pin.22 NC Pin.24 IO2 Pin.38 GND Pin.15 GND Pin.16 IO13 Pin.17 NC Pin.18 NC Pin.19 NC Flash and PSRAM NC: No component. The values of C15, L4 and C14 vary with the actual PCB board. EPAD PCB ANTENNA ESP32-WROVER-E(pin-out) The values of C1 and C2 vary with the selection of the crystal. The value of R2 varies with the actual PCB board. ESP32-D0WDR2-V3 ESP32-D0WD-V3 When ESP32-D0WDR2-V3 is used, U4 will be NC. GPIO16 SRAM_CLK GPIO33 GPIO25 GPIO26 GPIO27 GPIO14 FLASH_CLK SCS/CMD SHD/SD2 SWP/SD3 SDI/SD1 SDO/SD0 SCK/CLK GPIO17 SDO/SD0 SWP/SD3 SHD/SD2 SDI/SD1 EN GPIO35 SENSOR_VP SENSOR_VN GPIO34 GPIO32 U0RXD GPIO22 GPIO21 GPIO33 GPIO25 GPIO26 GPIO27 GPIO14 GPIO13 GPIO15 GPIO2 GPIO0 GPIO4 GPIO16 GPIO17 SHD/SD2 SWP/SD3 SCS/CMD SCK/CLK SDO/SD0 SDI/SD1 GPIO5 GPIO18 GPIO23 GPIO19 RF_ANT U0TXD EN SENSOR_VP GPIO35 GPIO32 SENSOR_VN GPIO34 GPIO12 GPIO12 GPIO13 GPIO23 GPIO22 U0TXD U0RXD GPIO21 GPIO19 GPIO18 GPIO5 GPIO4 GPIO0 GPIO2 GPIO15 ANT2 LNA_IN ANT1 SRAM_CLK FLASH_CLK GND VDD_SDIO GND GND VDD_SDIO VDD33 VDD_SDIO GND VDD33 GND GND GND GND VDD33 GND GND GND GND GND GND GND VDD33 GND GND GND VDD33 GND GND VDD33 GND GND GND VDD33 GND VDD33 GND GND VDD_SDIO GND Title Size Page Name Rev Date: Sheet o f Confidential and Proprietary V1.0 C 2 2Monday, July 04, 2022 Title Size Page Name Rev Date: Sheet o f Confidential and Proprietary V1.0 C 2 2Monday, July 04, 2022 Title Size Page Name Rev Date: Sheet o f Confidential and Proprietary V1.0 C 2 2Monday, July 04, 2022 R3 499 C14 TBD R15 0 R13 0 U4 PSRAM CS# 1 SO/SIO1 2 SIO2 3 VSS 4 SI/SIO0 5 SCLK 6 SIO3 7 VDD 8 C9 0.1uF R12 0 C11 1uF C20 1uF C10 0.1uF D1 ESD C4 0.1uF R1 20K(5%) C2 TBD C15 TBD C13 10uF C1 TBD R10 10K C6 3.3nF/6.3V(10%) C19 0.1uF R14 0(NC) R4 2K(NC) ANT1 PCB_ANT 1 2 L5 2.0nH(0.1nH) C21 NC R910K(NC) C5 10nF/6.3V(10%) C3 100pF U3 FLASH /CS 1 DO 2 /WP 3 GND 4 DI 5 CLK 6 /HOLD 7 VCC 8 J39 IPEX(NC) 1 2 3 R11 0(NC) C24 1uF U1 40MHz(±10ppm) XIN 1 GND 2 XOUT 3 GND 4 R2 0 U2 VDDA 1 LNA_IN 2 VDD3P3 3 VDD3P3 4 SENSOR_VP 5 SENSOR_CAPP 6 SENSOR_CAPN 7 SENSOR_VN 8 CHIP_PU 9 VDET_1 10 VDET_2 11 32K_XP 12 32K_XN 13 GPIO25 14 GPIO26 15 GPIO27 16 MTMS 17 MTDI 18 VDD3P3_RTC 19 MTCK 20 MTDO 21 GPIO2 22 GPIO0 23 GPIO4 24 VDD_SDIO 26 GPIO16 25 GPIO17 27 SD_DATA_2 28 SD_DATA_3 29 SD_CMD 30 SD_CLK 31 SD_DATA_0 32 GND 49 SD_DATA_1 33 GPIO5 34 GPIO18 35 GPIO19 38 CAP2 47 VDDA 43 XTAL_N 44 XTAL_P 45 GPIO23 36 U0TXD 41 GPIO22 39 GPIO21 42 VDD3P3_CPU 37 CAP1 48 VDDA 46 U0RXD 40 L4 TBD Figure 9: Schematics of ESP32-WROVER-E Espressif Systems 37 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 8 Module Schematics 5 5 4 4 3 3 2 2 1 1 D D C C B B A A Pin.1 GND Pin.2 3V3 Pin.3 EN Pin.4 SENSOR_VP Pin.5 SENSOR_VN Pin.6 IO34 Pin.7 IO35 Pin.8 IO32 Pin.9 IO33 Pin.10 IO25 Pin.11 IO26 Pin.12 IO27 Pin.13 IO14 Pin.23 IO15 Pin.37 IO23 Pin.36 IO22 Pin.28 NC Pin.32 NC Pin.27 NC Pin.25 IO0 Pin.35 U0TXD Pin.30 IO18 Pin.26 IO4 Pin.34 U0RXD Pin.29 IO5 Pin.33 IO21 Pin.31 IO19 Pin.14 IO12 Pin.20 NC Pin.21 NC Pin.22 NC Pin.24 IO2 Pin.38 GND Pin.15 GND Pin.16 IO13 Pin.17 NC Pin.18 NC Pin.19 NC Flash and PSRAM NC: No component. The values of C15, L4 and C14 vary with the actual PCB board. EPAD PCB ANTENNA ESP32-WROVER-IE(pin-out) The values of C1 and C2 vary with the selection of the crystal. The value of R2 varies with the actual PCB board. ESP32-D0WDR2-V3 ESP32-D0WD-V3 When ESP32-D0WDR2-V3 is used, U4 will be NC. GPIO16 SRAM_CLK GPIO33 GPIO25 GPIO26 GPIO27 GPIO14 FLASH_CLK SCS/CMD SHD/SD2 SWP/SD3 SDI/SD1 SDO/SD0 SCK/CLK GPIO17 SDO/SD0 SWP/SD3 SHD/SD2 SDI/SD1 EN GPIO35 SENSOR_VP SENSOR_VN GPIO34 GPIO32 U0RXD GPIO22 GPIO21 GPIO33 GPIO25 GPIO26 GPIO27 GPIO14 GPIO13 GPIO15 GPIO2 GPIO0 GPIO4 GPIO16 GPIO17 SHD/SD2 SWP/SD3 SCS/CMD SCK/CLK SDO/SD0 SDI/SD1 GPIO5 GPIO18 GPIO23 GPIO19 RF_ANT U0TXD EN SENSOR_VP GPIO35 GPIO32 SENSOR_VN GPIO34 GPIO12 GPIO12 GPIO13 GPIO23 GPIO22 U0TXD U0RXD GPIO21 GPIO19 GPIO18 GPIO5 GPIO4 GPIO0 GPIO2 GPIO15 ANT2 LNA_IN ANT1 SRAM_CLK FLASH_CLK GND VDD_SDIO GND GND VDD_SDIO VDD33 VDD_SDIO GND VDD33 GND GND GND GND VDD33 GND GND GND GND GND GND GND VDD33 GND GND GND VDD33 GND GND VDD33 GND GND GND VDD33 GND VDD33 GND GND VDD_SDIO GND Title Size Page Name Rev Date: Sheet o f Confidential and Proprietary V1.3 C 2 2Monday, July 04, 2022 Title Size Page Name Rev Date: Sheet o f Confidential and Proprietary V1.3 C 2 2Monday, July 04, 2022 Title Size Page Name Rev Date: Sheet o f Confidential and Proprietary V1.3 C 2 2Monday, July 04, 2022 R3 499 C14 TBD R15 0(NC) R13 0 U4 PSRAM CS# 1 SO/SIO1 2 SIO2 3 VSS 4 SI/SIO0 5 SCLK 6 SIO3 7 VDD 8 C9 0.1uF R12 0 C11 1uF C20 1uF C10 0.1uF D1 ESD C4 0.1uF R1 20K(5%) C2 TBD C15 TBD C13 10uF C1 TBD R10 10K C6 3.3nF/6.3V(10%) C19 0.1uF R14 0 R4 2K(NC) ANT1 PCB_ANT 1 2 L5 2.0nH(0.1nH) C21 NC R910K(NC) C5 10nF/6.3V(10%) C3 100pF U3 FLASH /CS 1 DO 2 /WP 3 GND 4 DI 5 CLK 6 /HOLD 7 VCC 8 J39 IPEX 1 2 3 R11 0(NC) C24 1uF U1 40MHz(±10ppm) XIN 1 GND 2 XOUT 3 GND 4 R2 0 U2 VDDA 1 LNA_IN 2 VDD3P3 3 VDD3P3 4 SENSOR_VP 5 SENSOR_CAPP 6 SENSOR_CAPN 7 SENSOR_VN 8 CHIP_PU 9 VDET_1 10 VDET_2 11 32K_XP 12 32K_XN 13 GPIO25 14 GPIO26 15 GPIO27 16 MTMS 17 MTDI 18 VDD3P3_RTC 19 MTCK 20 MTDO 21 GPIO2 22 GPIO0 23 GPIO4 24 VDD_SDIO 26 GPIO16 25 GPIO17 27 SD_DATA_2 28 SD_DATA_3 29 SD_CMD 30 SD_CLK 31 SD_DATA_0 32 GND 49 SD_DATA_1 33 GPIO5 34 GPIO18 35 GPIO19 38 CAP2 47 VDDA 43 XTAL_N 44 XTAL_P 45 GPIO23 36 U0TXD 41 GPIO22 39 GPIO21 42 VDD3P3_CPU 37 CAP1 48 VDDA 46 U0RXD 40 L4 TBD Figure 10: Schematics of ESP32-WROVER-IE Espressif Systems 38 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 9 Peripheral Schematics 9 Peripheral Schematics This is the typical application circuit of the module connected with peripheral components (for example, power supply, antenna, reset button, JTAG interface, and UART interface). 5 5 4 4 3 3 2 2 1 1 D D C C B B A A IO12 should be kept low when the module is powered on. EN SENSOR_VP SENSOR_VN IO34 IO35 IO32 IO33 IO25 IO26 IO27 IO14 IO13 IO22 TXD0 RXD0 IO21 IO19 IO18 IO4 IO0 IO5 IO23 IO15 IO2 IO12 ENIO14 TMS IO12 TDI IO13 TCK IO15 TDO GND VDD33 GND VDD33 GND GND GND GND GND SW1 R1 TBD R2 0R JP2 Boot Option 1 1 2 2 C2 0.1uF JP1 UART 1 1 2 2 3 3 4 4 JP3 JTAG 1 1 2 2 3 3 4 4 C3 TBD U1 ESP32-WROVER-E/ESP32-WROVER-IE GND1 1 3V3 2 EN 3 SENSOR_VP 4 SENSOR_VN 5 IO34 6 IO35 7 IO32 8 IO33 9 IO25 10 IO26 11 IO27 12 IO14 13 IO12 14 GND2 15 IO13 16 NC 17 NC 18 NC 19 NC 20 NC 21 NC 22 IO15 23 IO2 24 IO0 25 IO4 26 NC 27 NC 28 IO5 29 IO18 30 IO19 31 NC 32 IO21 33 RXD0 34 TXD0 35 IO22 36 IO23 37 GND3 38 P_GND 39 C4 0.1uF C1 22uF Figure 11: Peripheral Schematics • Soldering the EPAD to the ground of the base board is not a must, however, it can optimize thermal performance. If you choose to solder it, please apply the correct amount of soldering paste. Too much soldering paste may increase the gap between the module and the baseboard. As a result, the adhesion between other pins and the baseboard may be poor. • To ensure that the power supply to the ESP32 chip is stable during power-up, it is advised to add an RC delay circuit at the EN pin. The recommended setting for the RC delay circuit is usually R = 10 kΩ and C = 1 µF. However, specific parameters should be adjusted based on the power-up timing of the module and the power-up and reset sequence timing of the chip. For ESP32’s power-up and reset sequence timing diagram, please refer to Section 4.6 Chip Power-up and Reset. • UART0 is used to download firmware and log output. When using the AT firmware, note that the UART GPIO is already configured. It is recommended to use the default configuration. Please refer to ESP-AT User Guide for ESP32 > Section Hardware Connection. Espressif Systems 39 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 10 Physical Dimensions 10 Physical Dimensions 10.1 Module Dimensions 1.27 38 x 0.9 1.0838 x 0.45 38 x 0.85 0.5 0.46 0.8 3.7 1.1 31.4±0.15 22.86 38 x 0.9 3.3±0.15 Top View Side View Bottom View 18±0.15 6.22 0.9 Unit: mm 0.9 3.7 16.16 7.5 38 x Ø0.55 10.45 15.84 24.09 20.37 1.27 38 x 0.9 1.08 38 x 0.45 38 x 0.85 0.5 0.46 0.8 3.7 1.1 31.4±0.15 22.86 38 x 0.9 3.3±0.15 Top View Side View Bottom View 18±0.15 6.22 0.9 Unit: mm 0.9 3.7 16.16 7.5 38 x Ø0.55 10.45 15.84 24.09 20.37 23.05 2.25 Figure 12: ESP32-WROVER-E Physical Dimensions Espressif Systems 40 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 10 Physical Dimensions 1.27 38 x 0.9 1.0838 x 0.45 38 x 0.85 0.5 0.46 0.8 3.7 1.1 31.4±0.15 22.86 38 x 0.9 3.3±0.15 Top View Side View Bottom View 18±0.15 6.22 0.9 Unit: mm 0.9 3.7 16.16 7.5 38 x Ø0.55 10.45 15.84 24.09 20.37 1.27 38 x 0.9 1.08 38 x 0.45 38 x 0.85 0.5 0.46 0.8 3.7 1.1 31.4±0.15 22.86 38 x 0.9 3.3±0.15 Top View Side View Bottom View 18±0.15 6.22 0.9 Unit: mm 0.9 3.7 16.16 7.5 38 x Ø0.55 10.45 15.84 24.09 20.37 23.05 2.25 Figure 13: ESP32-WROVER-IE Physical Dimensions Note: For information about tape, reel, and product marking, please refer to ESP32 Module Packaging Information. Espressif Systems 41 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 10 Physical Dimensions 10.2 Dimensions of External Antenna Connector ESP32-WROVER-IE uses the first generation external antenna connector as shown in Figure 14. This connector is compatible with the following connectors: • U.FL Series connector from Hirose • MHF I connector from I-PEX • AMC connector from Amphenol Unit: mm Figure 14: Dimensions of External Antenna Connector The external antenna used for ESP32-WROVER-IE during certification testing is the first generation monopole antenna, with material code TFPD05H08750011. Espressif Systems 42 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 10 Physical Dimensions The module does not include an external antenna upon shipment. If needed, select a suitable external antenna based on the product’s usage environment and performance requirements. It is recommended to select an antenna that meets the following requirements: • 2.4 GHz band • 50 Ω impedance • The maximum gain does not exceed 2.33 dBi, the gain of the antenna used for certification • The connector matches the specifications shown in Figure 14 Dimensions of External Antenna Connector Note: If you use an external antenna of a different type or gain, additional testing, such as EMC, may be required beyond the existing antenna test reports for Espressif modules. Specific requirements depend on the certification type. Espressif Systems 43 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 11 PCB Layout Recommendations 11 PCB Layout Recommendations 11.1 PCB Land Pattern This section provides the following resources for your reference: • Figures for recommended PCB land patterns with all the dimensions needed for PCB design. See Figure 15 Recommended PCB Land Pattern. • Source files of recommended PCB land patterns to measure dimensions not covered in Figure 15. You can view the source files for ESP32-WROVER-E and ESP32-WROVER-IE with Autodesk Viewer. • 3D models of ESP32-WROVER-E and ESP32-WROVER-IE. Please make sure that you download the 3D model file in .STEP format (beware that some browsers might add .txt). 18 1.27 3.7 0.9 38 x0.9 38 x1.5 3.7 6.22 7.5 0.9 1.27 0.5 Unit: mm Copper Via for thermal pad 17.5 16.16 22.86 31.4 7.44 Antenna Area 1 19 20 38 1.1 0.5 Figure 15: Recommended PCB Land Pattern Espressif Systems 44 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 11 PCB Layout Recommendations 11.2 Module Placement for PCB Design If module-on-board design is adopted, attention should be paid while positioning the module on the base board. The interference of the base board on the module’s antenna performance should be minimized. For details about module placement for PCB design, please refer to ESP32 Hardware Design Guidelines > Section Positioning a Module on a Base Board. Espressif Systems 45 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 12 Product Handling 12 Product Handling 12.1 Storage Conditions The products sealed in moisture barrier bags (MBB) should be stored in a non-condensing atmospheric environment of < 40 °C and 90%RH. The module is rated at the moisture sensitivity level (MSL) of 3. After unpacking, the module must be soldered within 168 hours with the factory conditions 25 ± 5 °C and 60 %RH. If the above conditions are not met, the module needs to be baked. 12.2 Electrostatic Discharge (ESD) • Human body model (HBM): ±2000 V • Charged-device model (CDM): ±500 V 12.3 Reflow Profile Solder the module in a single reflow. 50 150 0 25 1 ~ 3 ℃/s 0 200 250 200 –1 ~ –5 ℃/s Cooling zone 100 217 50 100 250 Reflow zone 217 ℃ 60 ~ 90 s Temperature (℃) Preheating zone 150 ~ 200 ℃ 60 ~ 120 s Ramp-up zone Peak Temp. 235 ~ 250 ℃ Soldering time > 30 s Time (sec.) Ramp-up zone — Temp.: 25 ~ 150 ℃ Time: 60 ~ 90 s Ramp-up rate: 1 ~ 3 ℃/s Preheating zone — Temp.: 150 ~ 200 ℃ Time: 60 ~ 120 s Reflow zone — Temp.: >217 ℃ 60 ~ 90 s; Peak Temp.: 235 ~ 250 ℃ Time: 30 ~ 70 s Cooling zone — Peak Temp. ~ 180 ℃ Ramp-down rate: –1 ~ –5 ℃/s Solder — Sn-Ag-Cu (SAC305) lead-free solder alloy Figure 16: Reflow Profile Espressif Systems 46 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 12 Product Handling 12.4 Ultrasonic Vibration Avoid exposing Espressif modules to vibration from ultrasonic equipment, such as ultrasonic welders or ultrasonic cleaners. This vibration may induce resonance in the in-module crystal and lead to its malfunction or even failure. As a consequence, the module may stop working or its performance may deteriorate. Espressif Systems 47 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Datasheet Versioning Datasheet Versioning Datasheet Version Status Watermark Definition v0.1 ~ v0.5 (excluding v0.5) Draft Confidential This datasheet is under development for products in the design stage. Specifications may change without prior notice. v0.5 ~ v1.0 (excluding v1.0) Preliminary release Preliminary This datasheet is actively updated for products in the verification stage. Specifications may change before mass production, and the changes will be documentation in the datasheet’s Revision History. v1.0 and higher Official release — This datasheet is publicly released for products in mass production. Specifications are finalized, and major changes will be communicated via Product Change Notifications (PCN). Any version — Not Recommended for New Design (NRND) 1 This datasheet is updated less frequently for products not recommended for new designs. Any version — End of Life (EOL) 2 This datasheet is no longer mtained for products that have reached end of life. 1 Watermark will be added to the datasheet title page only when all the product variants covered by this datasheet are not recommended for new designs. 2 Watermark will be added to the datasheet title page only when all the product variants covered by this datasheet have reached end of life. Espressif Systems 48 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Related Documentation and Resources Related Documentation and Resources Related Documentation • ESP32 Series Datasheet – Specifications of the ESP32 hardware. • ESP32 Technical Reference Manual – Detailed information on how to use the ESP32 memory and peripherals. • ESP32 Hardware Design Guidelines – Guidelines on how to integrate the ESP32 into your hardware product. • ESP32 ECO and Workarounds for Bugs – Correction of ESP32 design errors. • ESP32 Series SoC Errata – Descriptions of known errors in ESP32 series of SoCs. • Certificates https://espressif.com/en/support/documents/certificates • ESP32 Product/Process Change Notifications (PCN) https://espressif.com/en/support/documents/pcns • ESP32 Advisories – Information on security, bugs, compatibility, component reliability. https://espressif.com/en/support/documents/advisories • Documentation Updates and Update Notification Subscription https://espressif.com/en/support/download/documents Developer Zone • ESP-IDF Programming Guide for ESP32 – Extensive documentation for the ESP-IDF development framework. • ESP-IDF and other development frameworks on GitHub. https://github.com/espressif • ESP32 BBS Forum – Engineer-to-Engineer (E2E) Community for Espressif products where you can post questions, share knowledge, explore ideas, and help solve problems with fellow engineers. https://esp32.com/ • ESP-FAQ – A summary document of frequently asked questions released by Espressif. https://espressif.com/projects/esp-faq/en/latest/index.html • The ESP Journal – Best Practices, Articles, and Notes from Espressif folks. https://blog.espressif.com/ • See the tabs SDKs and Demos, Apps, Tools, AT Firmware. https://espressif.com/en/support/download/sdks-demos Products • ESP32 Series SoCs – Browse through all ESP32 SoCs. https://espressif.com/en/products/socs?id=ESP32 • ESP32 Series Modules – Browse through all ESP32-based modules. https://espressif.com/en/products/modules?id=ESP32 • ESP32 Series DevKits – Browse through all ESP32-based devkits. https://espressif.com/en/products/devkits?id=ESP32 • ESP Product Selector – Find an Espressif hardware product suitable for your needs by comparing or applying filters. https://products.espressif.com/#/product-selector?language=en Contact Us • See the tabs Sales Questions, Technical Enquiries, Circuit Schematic & PCB Design Review, Get Samples (Online stores), Become Our Supplier, Comments & Suggestions. https://espressif.com/en/contact-us/sales-questions Espressif Systems 49 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Revision History Revision History Date Version Release notes 2025-12-29 v2.3 Table 1 Series Comparison and Table 2 Series Comparison: • Marked ESP32-WROVER-E/IE-N4R2, ESP32-WROVER-E/IE-N8R2, ESP32-WROVER-E/IE-N16R2 as ”End of Life” (EOL) • Updated ”Ordering Code” to ”Part Number” 2025-10-20 v2.2 • Updated Figure 6 Visualization of Timing Parameters for the Strapping Pins • Table 15 DC Characteristics (3.3 V, 25 °C): Added V IH_nRST • Added notes about the external antenna connector in Section 10.2 Dimen- sions of External Antenna Connector • Added Section Datasheet Versioning 2025-06-27 v2.1 • Table 1 and 2: Added VDD_SDIO voltage • Section 2 Block Diagram: Added a note about pin mapping between the chip and the in-package flash/PSRAM • Added Section 4.6 Chip Power-up and Reset • Added Section 6.5 Memory Specifications 2024-11-12 v2.0 • Improved the wording and structure of following sections: – Updated Section ”Strapping Pins” and renamed to Boot Configurations – Added Chapter 5 Peripherals – Updated Table ”Wi-Fi RF Standards” and renamed to Wi-Fi RF Char- acteristics – Section 9 Peripheral Schematics: Added a note about UART 2023-11-21 v1.9 • Table 1 Series Comparison: Added information about flash • Figure 9 Peripheral Schematics: Updated the note about soldering • Section 10.2 Dimensions of External Antenna Connector: Added information about the antenna external connector 2023-02-09 v1.8 • Major updates: – Removed contents about hall sensor according to PCN20221202 • Other updates: – Added source files of PCB land patterns and 3D models of the mod- ules (if available) in Section 11.1 PCB Land Pattern 2022-12-02 v1.7 Updated Figure 10.1 Module Dimensions and 11.1 PCB Land Pattern Espressif Systems 50 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Revision History Date Version Release notes 2022-07-20 v1.6 • Added module variants embedded with ESP32-D0WDR2-V3 chip • Added Table 1 ESP32-WROVER-E Series Comparison and Table 2 ESP32- WROVER-IE Series Comparison • Added Figure 6 Visualization of Timing Parameters for the Strapping Pins and Table 5 Description of Timing Parameters for the Strapping Pins in Section 4 Boot Configurations • Updated Related Documentation and Resources 2022-02-22 v1.5 • Replaced Espressif Product Ordering Information with ESP Product Selector • Updated the description of TWAI in Section 1.1 Features • Added a link to RF certificates in Section 1.1 Features • Updated Ordering Information Table • Updated Table 13 Absolute Maximum Ratings • Fixed typos 2021-02-09 v1.4 • Updated Figure 12 ESP32-WROVER-E Physical Dimensions • Updated Figure 15 Recommended PCB Land Pattern 2021-02-02 v1.3 • Updated the trade mark from TWAI™ to TWAI ® • Deleted Reset Circuit and Discharge Circuit for VDD33 Rail in Section 9 Peripheral Schematics • Modified the note below Figure 16 Reflow Profile 2020-11-02 v1.2 • Updated Figure 3.1 Pin Layout • Added a note to EPAD in Section 11.1 PCB Land Pattern • Updated the note to RC delay circuit in Section 9 Peripheral Schematics 2020-06-11 v1.1 • Updated Figure 1 ESP32-WROVER-E Block Diagram (with ESP32-D0WD- V3 embedded) • Updated Figure 2 ESP32-WROVER-E Block Diagram (with ESP32- D0WDR2-V3 embedded) 2020-05-22 v1.0 Official release Espressif Systems 51 Submit Documentation Feedback ESP32-WROVER-E & ESP32-WROVER-IE Datasheet v2.3 Disclaimer and Copyright Notice Information in this document, including URL references, is subject to change without notice. ALL THIRD PARTY’S INFORMATION IN THIS DOCUMENT IS PROVIDED AS IS WITH NO WARRANTIES TO ITS AUTHENTICITY AND ACCURACY. NO WARRANTY IS PROVIDED TO THIS DOCUMENT FOR ITS MERCHANTABILITY, NON-INFRINGEMENT, FITNESS FOR ANY PARTICULAR PURPOSE, NOR DOES ANY WARRANTY OTHERWISE ARISING OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE. All liability, including liability for infringement of any proprietary rights, relating to use of information in this document is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are granted herein. The Wi-Fi Alliance Member logo is a trademark of the Wi-Fi Alliance. The Bluetooth logo is a registered trademark of Bluetooth SIG. All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged. Copyright © 2025 Espressif Systems (Shanghai) Co., Ltd. All rights reserved. www.espressif.com